特点:
1、综合性能较好,冲击强度较高,化学稳定性,电性能良好.
2、与372有机玻璃的熔接性良好,制成双色塑件,且可表面镀铬,喷漆处理.
3、有高抗冲、高耐热、阻燃、增强、透明等级别。
4、流动性比HIPS差一点,比PMMA、PC等好,柔韧性好。
5、用途:适于制作一般机械零件,减磨耐磨零件,传动零件和电讯零件.
6、同PVC(聚氯乙烯)一样在屈折处会出现白化现象。
(参考图)
典型应用范Χ:
汽车内外饰:仪表板,饰柱,仪表前盖,格栅,内外饰件 2.商务设备机壳和内置部件:笔记本/台式电脑,复印机,打印机,绘图仪,显示器 3.电信,移动电话外壳,附件以及智能卡(SIM卡): 4.电器产品,电子产品外壳,电表罩和壳体,家用开关,插头和插座,电缆电线管道 5.家用电器,如洗衣机,吹风机,微波¯内外部件等。
物性表: | |||||
Physical Properties | Metric | English | Comments | ||
---|---|---|---|---|---|
Specific Gravity | 1.19 g/cc | 1.19 g/cc | ASTM D792 | ||
Density | 1.20 g/cc | 0.0434 lb/in³ | ISO 1183 | ||
Linear Mold Shrinkage, Flow | 0.00050 - 0.00070 cm/cm | 0.00050 - 0.00070 in/in | on Tensile Bar; SABIC Method | ||
0.0040 - 0.0050 cm/cm @Thickness 3.20 mm |
0.0040 - 0.0050 in/in @Thickness 0.126 in |
SABIC Method | |||
Melt Flow | 6.3 g/10 min @Load 2.16 kg, Temperature 260 °C |
6.3 g/10 min @Load 4.76 lb, Temperature 500 °F |
ASTM D1238 | ||
Melt Index of Compound | 16 g/10 min @Load 5.00 kg, Temperature 260 °C |
16 g/10 min @Load 11.0 lb, Temperature 500 °F |
MVR [cm^3/10 min]; ISO 1133 | ||
Mechanical Properties | Metric | English | Comments | ||
Hardness, H358/30 | 100 MPa | 14500 psi | ISO 2039-1 | ||
Tensile Strength at Break | 54.0 MPa | 7830 psi | Type I, 50 mm/min; ASTM D638 | ||
55.0 MPa | 7980 psi | 50 mm/min; ISO 527 | |||
Tensile Strength, Yield | 63.0 MPa | 9140 psi | Type I, 50 mm/min; ASTM D638 | ||
63.0 MPa | 9140 psi | 50 mm/min; ISO 527 | |||
Elongation at Break | 88 % | 88 % | Type I, 50 mm/min; ASTM D638 | ||
95 % | 95 % | 50 mm/min; ISO 527 | |||
Elongation at Yield | 5.0 % | 5.0 % | 50 mm/min; ISO 527 | ||
5.5 % | 5.5 % | Type I, 50 mm/min; ASTM D638 | |||
Tensile Modulus | 2.30 GPa | 334 ksi | 1 mm/min; ISO 527 | ||
2.54 GPa | 368 ksi | 50 mm/min; ASTM D638 | |||
Flexural Yield Strength | 90.0 MPa | 13100 psi | 2 mm/min; ISO 178 | ||
95.0 MPa | 13800 psi | 1.3 mm/min, 50 mm span; ASTM D790 | |||
Flexural Modulus | 2.40 GPa | 348 ksi | 2 mm/min; ISO 178 | ||
2.59 GPa | 376 ksi | 1.3 mm/min, 50 mm span; ASTM D790 | |||
Izod Impact, Notched | 9.07 J/cm | 17.0 ft-lb/in | ASTM D256 | ||
Izod Impact, Notched (ISO) | 50.0 kJ/m² | 23.8 ft-lb/in² | 80*10*4; ISO 180/1A | ||
15.0 kJ/m² @Temperature -30.0 °C |
7.14 ft-lb/in² @Temperature -22.0 °F |
80*10*4; ISO 180/1A | |||
19.0 kJ/m² @Temperature 0.000 °C |
9.04 ft-lb/in² @Temperature 32.0 °F |
80*10*4; ISO 180/1A | |||
Charpy Impact, Notched | 5.50 J/cm² | 26.2 ft-lb/in² | Edgew 80*10*4 sp=62mm; ISO 179/1eA | ||
1.50 J/cm² @Temperature -30.0 °C |
7.14 ft-lb/in² @Temperature -22.0 °F |
Edgew 80*10*4 sp=62mm; ISO 179/1eA | |||
Dart Drop, Total Energy | 72.0 J @Temperature 23.0 °C |
53.1 ft-lb @Temperature 73.4 °F |
ASTM D3763 | ||
Electrical Properties | Metric | English | Comments | ||
Volume Resistivity | >= 1.00e+15 ohm-cm | >= 1.00e+15 ohm-cm | IEC 60093 | ||
Surface Resistance | >= 1.00e+15 ohm | >= 1.00e+15 ohm | ROA; IEC 60093 | ||
Dielectric Constant | 2.7 @Frequency 1.00e+6 Hz |
2.7 @Frequency 1.00e+6 Hz |
IEC 60250 | ||
2.7 @Frequency 50.0 - 60.0 Hz |
2.7 @Frequency 50.0 - 60.0 Hz |
IEC 60250 | |||
Dielectric Strength | 18.0 kV/mm @Thickness 3.20 mm |
457 kV/in @Thickness 0.126 in |
in oil; IEC 60243-1 | ||
Dissipation Factor | 0.0010 @Frequency 50.0 - 60.0 Hz |
0.0010 @Frequency 50.0 - 60.0 Hz |
IEC 60250 | ||
0.010 @Frequency 1.00e+6 Hz |
0.010 @Frequency 1.00e+6 Hz |
IEC 60250 | |||
Comparative Tracking Index | 225 V | 225 V | IEC 60112 | ||
Thermal Properties | Metric | English | Comments | ||
CTE, linear, Parallel to Flow | 70.0 µm/m-°C @Temperature 23.0 - 60.0 °C |
38.9 µin/in-°F @Temperature 73.4 - 140 °F |
ISO 11359-2 | ||
77.4 µm/m-°C @Temperature -40.0 - 40.0 °C |
43.0 µin/in-°F @Temperature -40.0 - 104 °F |
ASTM E 831 | |||
CTE, linear, Transverse to Flow | 59.4 µm/m-°C @Temperature -40.0 - 40.0 °C |
33.0 µin/in-°F @Temperature -40.0 - 104 °F |
ASTM E 831 | ||
70.0 µm/m-°C @Temperature 23.0 - 60.0 °C |
38.9 µin/in-°F @Temperature 73.4 - 140 °F |
ISO 11359-2 | |||
Deflection Temperature at 0.46 MPa (66 psi) | 126 °C | 259 °F | Edgew 120*10*4 sp=100mm; ISO 75/Be | ||
127 °C @Thickness 3.20 mm |
261 °F @Thickness 0.126 in |
unannealed; ASTM D648 | |||
Deflection Temperature at 1.8 MPa (264 psi) | 113 °C | 235 °F | Edgew 120*10*4 sp=100mm; ISO 75/Ae | ||
118 °C @Thickness 3.20 mm |
244 °F @Thickness 0.126 in |
unannealed; ASTM D648 | |||
Vicat Softening Point | 134 °C | 273 °F | Rate B/50; ISO 306 | ||
135 °C | 275 °F | Rate B/120; ISO 306 | |||
Flammability, UL94 | V-1 @Thickness 0.990 mm |
V-1 @Thickness 0.0390 in |
UL 94 | ||
V-0 @Thickness 1.49 mm |
V-0 @Thickness 0.0587 in |
UL 94 | |||
De |
|||||
Ball Pressure Test, 125°C +/- 2°C | PASSES | IEC 60695-10-2 |
上海松翰塑化科技有限公司,供应原料,品质真实,物实价廉。
PA6T,46,9T、PC、PC/ABS、PBT、ABS、PPA、PPS、POM、PMMA、TPE、PPO、LCP液晶聚合物。
欢迎各λ客户前来咨询:
联系人: 夏先生
手 机:13501802636 021 51131842
QQ :205730283
邮 箱 :205730283@qq.com