Geloy XTPM307|(PC+ASA)|沙特基础物性表报告及物性特性介绍,Geloy XTPM307|(PC+ASA)|沙特基础注塑参数详情-塑料物性表查询网

流变性能(Rheological properties)	值(Value)	单位(Unit)	测试标准(Test Standard)
ISO数据
熔体体积流动速率(Melt volume-flow rate) (MVR)	16	cm³/10min	ISO 1133
温度(Temperature)	260	°C	ISO 1133
负载(Load)	5	kg	ISO 1133

机械性能(机械性能(Mechanical properties))	值(Value)	单位(Unit)	测试标准(Test Standard)
ISO数据
拉伸模量(Tensile Modulus)	2350	MPa	ISO 527-1/-2
屈服应力(Yield stress)	58	MPa	ISO 527-1/-2
屈服应变(Yield strain)	4.7	%	ISO 527-1/-2
破坏时应变(Stress at break)	60	MPa	ISO 527-1/-2
破坏时应变(Strain at break)	>50	%	ISO 527-1/-2
弯曲弹性模量(Flexural modulus) (23°C)	2210	MPa	ISO 178
悬臂梁式冲击切口 (23°C)	59	kJ/m²	ISO 180/1A
悬臂梁式冲击切口	17	kJ/m²	ISO 180/1A
温度(Temperature)	-30	°C	ISO 180/1A
ASTM数据(ASTM Data)
拉伸模量(Tensile Modulus)	2280	MPa	ASTM D 638
抗拉强度(Tensile Strength) at Yield	57	MPa	ASTM D 638
抗拉强度(Tensile Strength) at Break	64	MPa	ASTM D 638
屈服伸长率(Elongation at Yield)	4.8	%	ASTM D 638
断裂伸长率(Elongation at Break)	100	%	ASTM D 638
悬臂梁式冲击切口 (1/8 in)	0.615	kJ/m	ASTM D 256
悬臂梁式冲击切口 (Low-温度(Temperature))	0.197	kJ/m	ASTM D 256
温度(Temperature)	-20	°C	ASTM D 256

热性能(热性能(Thermal properties))	值(Value)	单位(Unit)	测试标准(Test Standard)
ISO数据
温度负荷变形(Temp. of deflection under load) (1.80 MPa)	103	°C	ISO 75-1/-2
温度负荷变形(Temp. of deflection under load) (0.45 MPa)	125	°C	ISO 75-1/-2
Vicat softening temperature A	138	°C	ISO 306
维卡软化温度（50℃/ h的50N）Vicat softening temperature	116	°C	ISO 306
COEFF线性热(Coeff. of linear therm. expansion) (parallel)	80	E-6/K	ISO 11359-1/-2
COEFF线性热(Coeff. of linear therm. expansion) (normal)	80	E-6/K	ISO 11359-1/-2

电气性能(Electrical properties)	值(Value)	单位(Unit)	测试标准(Test Standard)
ASTM数据(ASTM Data)
绝缘强度(Dielectric Strength) (Short Time)	27.5	kV/mm	ASTM D 149
耗散因数(Dissipation Factor) (1 MHz)	0.0153	-	ASTM D 150
表面电阻率(Surface Resistivity)	>1E15	Ohm	ASTM D 257
体积电阻率(Volume Resistivity)	>1E15	Ohm*cm	ASTM D 257

其他属性(Other properties)	值(Value)	单位(Unit)	测试标准(Test Standard)
ISO数据
吸水率(Water absorption)	0.6	%	Sim. to ISO 62
吸湿性(Humidity absorption)	0.2	%	Sim. to ISO 62
密度(Density)	1150	kg/m³	ISO 1183

CharacteristicsProcessingInjection MoldingSpecial CharacteristicsHeat stabilized or stable to heatRegional AvailabilityEurope, Near East/AfricaDisclaimerCopyright M-Base .