塑胶原料之家
  1. 首页
  2. 英文物性
  3. PP
  4. Overview of materials for Polypropylene, Molded

Overview of materials for Polypropylene, Molded

Overview of materials for Polypropylene, Molded 物性表: Overview of materials for Polypropylene, Molded物性表及特性介绍,Overview of materials for Polypropylene, Molded注塑参数详情,如需Overview of materials for Polypropylene, Molded下载, 可到相关下载区下载
  • 熔体流动速率 [g/10min]: 0.2
  • 密度 [g/cm3]: 0.88
  • 缺口冲击强度: 0.09
  • 拉伸强度 [MPa]: 2.07
  • 断裂伸长率 [%]: 20.0
  • 弯曲强度 [MPa]: 9.0
  • 弯曲模量 [MPa]: 0.0260
  • 硬度: 20.0
  • 热变形温度 [℃]: 55.0
  • 脆化温度 [℃]: -20.0
  • 透光率 [%]: 84.0
 
Physical PropertiesMetricEnglishComments
Density 0.880 - 2.40 g/cc0.0318 - 0.0867 lb/in³Average value: 0.934 g/cc Grade Count:742
Water Absorption 0.000 - 1.00 %0.000 - 1.00 %Average value: 0.0714 % Grade Count:121
Moisture Absorption at Equilibrium 0.100 %0.100 %Average value: 0.100 % Grade Count:58
Water Absorption at Saturation 0.0100 %0.0100 %Average value: 0.0100 % Grade Count:5
Particle Size 300 - 2500 µm300 - 2500 µmAverage value: 900 µm Grade Count:9
Viscosity Measurement 80.0 - 500000
@Temperature 180 - 180 °C		80.0 - 500000
@Temperature 356 - 356 °F		Average value: 171000 Grade Count:3
Thickness 25.4 - 102 microns1.00 - 4.00 milAverage value: 88.9 microns Grade Count:6
Linear Mold Shrinkage 0.000500 - 0.0250 cm/cm0.000500 - 0.0250 in/inAverage value: 0.0132 cm/cm Grade Count:196
Linear Mold Shrinkage, 6.35 mm section 0.0250 cm/cm0.0250 in/inAverage value: 0.0250 cm/cm Grade Count:5
Linear Mold Shrinkage, Transverse 0.0100 - 0.0155 cm/cm0.0100 - 0.0155 in/inAverage value: 0.0134 cm/cm Grade Count:5
Melt Flow 0.200 - 1200 g/10 min0.200 - 1200 g/10 minAverage value: 23.2 g/10 min Grade Count:833
Base Resin Melt Index 0.500 - 50.0 g/10 min
@Temperature 230 - 230 °C		0.500 - 50.0 g/10 min
@Temperature 446 - 446 °F		Average value: 15.1 g/10 min Grade Count:17
Ash 0.00800 - 26.0 %0.00800 - 26.0 %Average value: 1.38 % Grade Count:20
Collected Volatile Condensable Material 0.0500 - 3.00 %0.0500 - 3.00 %Average value: 0.446 % Grade Count:25
 
Mechanical PropertiesMetricEnglishComments
Hardness, Rockwell R 20.0 - 11820.0 - 118Average value: 96.0 Grade Count:394
Hardness, Shore D 40.0 - 83.040.0 - 83.0Average value: 69.8 Grade Count:88
Ball Indentation Hardness 62.0 - 106 MPa8990 - 15400 psiAverage value: 85.5 MPa Grade Count:15
Tensile Strength, Ultimate 9.00 - 80.0 MPa1310 - 11600 psiAverage value: 30.3 MPa Grade Count:175
 10.0 - 23.0 MPa
@Temperature 60.0 - 120 °C		1450 - 3340 psi
@Temperature 140 - 248 °F		Average value: 16.0 MPa Grade Count:1
Tensile Strength, Yield 2.07 - 369 MPa300 - 53500 psiAverage value: 32.1 MPa Grade Count:766
Film Elongation at Break, MD 93.0 - 530 %93.0 - 530 %Average value: 258 % Grade Count:3
Elongation at Break 3.00 - 900 %3.00 - 900 %Average value: 160 % Grade Count:281
Elongation at Yield 3.50 - 100 %3.50 - 100 %Average value: 11.0 % Grade Count:562
Modulus of Elasticity 0.00800 - 8.25 GPa1.16 - 1200 ksiAverage value: 1.75 GPa Grade Count:223
Tenacity 0.203 - 0.441 N/tex2.30 - 5.00 g/denierAverage value: 0.308 N/tex Grade Count:8
Flexural Yield Strength 20.0 - 180 MPa2900 - 26100 psiAverage value: 44.6 MPa Grade Count:57
Flexural Modulus 0.0260 - 12.4 GPa3.77 - 1800 ksiAverage value: 1.44 GPa Grade Count:715
 0.350 - 0.680 GPa
@Temperature 60.0 - 120 °C		50.8 - 98.6 ksi
@Temperature 140 - 248 °F		Average value: 0.472 GPa Grade Count:2
Compressive Yield Strength 34.5 - 55.2 MPa5000 - 8000 psiAverage value: 39.0 MPa Grade Count:8
Compressive Modulus 1.38 GPa200 ksiAverage value: 1.38 GPa Grade Count:6
Shear Modulus 0.680 - 0.920 GPa98.6 - 133 ksiAverage value: 0.757 GPa Grade Count:10
Secant Modulus 0.0000689 - 2.20 GPa0.0100 - 319 ksiAverage value: 1.23 GPa Grade Count:3
 0.0000344738 - 0.0000344738 GPa
@Temperature -20.0 - -20.0 °C		0.00500008 - 0.00500008 ksi
@Temperature -4.00 - -4.00 °F		Average value: 0.0000345 GPa Grade Count:1
Izod Impact, Notched 0.0900 J/cm - NB0.169 ft-lb/in - NBAverage value: 0.764 J/cm Grade Count:629
 0.0400 - 1.17458 J/cm
@Temperature -40.0 - 0.000 °C		0.0749 - 2.20047 ft-lb/in
@Temperature -40.0 - 32.0 °F		Average value: 0.476 J/cm Grade Count:62
 1.00 - 1.35 J/cm
@Temperature -20.0 - -20.0 °C		1.87 - 2.53 ft-lb/in
@Temperature -4.00 - -4.00 °F		Average value: 0.476 J/cm Grade Count:2
 1.00 - 1.35 J/cm
@Diameter 3.17 - 3.17 mm		1.87 - 2.53 ft-lb/in
@Diameter 0.125 - 0.125 in		Average value: 0.476 J/cm Grade Count:2
Izod Impact, Unnotched 0.196 J/cm - NB0.367 ft-lb/in - NBAverage value: 8.39 J/cm Grade Count:57
 2.1356 - 2.1356 J/cm
@Temperature -18.0 - -18.0 °C		4.0009 - 4.0009 ft-lb/in
@Temperature -0.400 - -0.400 °F		Average value: 2.14 J/cm Grade Count:1
Izod Impact, Notched (ISO) 2.00 - 56.0 kJ/m²0.952 - 26.6 ft-lb/in²Average value: 7.89 kJ/m² Grade Count:74
 1.10 - 8.00 kJ/m²
@Temperature -40.0 - 2.00 °C		0.523 - 3.81 ft-lb/in²
@Temperature -40.0 - 35.6 °F		Average value: 4.02 kJ/m² Grade Count:26
Izod Impact, Unnotched (ISO) NBNBGrade Count:6
Charpy Impact Unnotched 0.300 J/cm² - NB1.43 ft-lb/in² - NBAverage value: 7.62 J/cm² Grade Count:116
 0.700 J/cm² - NB
@Temperature -50.0 - -20.0 °C		3.33 ft-lb/in² - NB
@Temperature -58.0 - -4.00 °F		Average value: 4.06 J/cm² Grade Count:94
Charpy Impact, Notched 0.200 - 9.50 J/cm²0.952 - 45.2 ft-lb/in²Average value: 1.11 J/cm² Grade Count:121
 0.130 - 1.70 J/cm²
@Temperature -30.0 - 10.0 °C		0.619 - 8.09 ft-lb/in²
@Temperature -22.0 - 50.0 °F		Average value: 0.367 J/cm² Grade Count:85
Gardner Impact 0.904 - 40.7 J0.667 - 30.0 ft-lbAverage value: 11.5 J Grade Count:48
 1.99983 - 30.393 J
@Temperature -30.0 - -18.0 °C		1.47500 - 22.417 ft-lb
@Temperature -22.0 - -0.400 °F		Average value: 19.9 J Grade Count:24
 15.0225 - 23.9528 J
@Temperature -30.0 - -30.0 °C		11.0800 - 17.6667 ft-lb
@Temperature -22.0 - -22.0 °F		Average value: 19.9 J Grade Count:8
 15.0225 - 23.9528 J
@Thickness 3.17 - 3.20 mm		11.0800 - 17.6667 ft-lb
@Thickness 0.125 - 0.126 in		Average value: 19.9 J Grade Count:8
Falling Dart Impact 4.98 - 28.0 J3.67 - 20.7 ft-lbAverage value: 10.8 J Grade Count:5
Coefficient of Friction 0.2500.250Average value: 0.250 Grade Count:6
Tensile Creep Modulus, 1 hour 550 - 700 MPa79800 - 102000 psiAverage value: 657 MPa Grade Count:7
Tensile Creep Modulus, 1000 hours 220 - 440 MPa31900 - 63800 psiAverage value: 349 MPa Grade Count:7
Tear Strength 20.2 - 226 kN/m115 - 1290 pliAverage value: 102 kN/m Grade Count:7
Compression Set 16.0 - 65.0 %16.0 - 65.0 %Average value: 33.2 % Grade Count:4
Film Tensile Strength at Break, MD 3.10 - 152 MPa450 - 22000 psiAverage value: 70.1 MPa Grade Count:3
Tangent Modulus 1290 - 3260 MPa187000 - 472000 psiAverage value: 1920 MPa Grade Count:4
 
Electrical PropertiesMetricEnglishComments
Electrical Resistivity 1000 - 1.00e+18 ohm-cm1000 - 1.00e+18 ohm-cmAverage value: 1.23e+17 ohm-cm Grade Count:104
Surface Resistance 100 - 1.00e+15 ohm100 - 1.00e+15 ohmAverage value: 1.23e+14 ohm Grade Count:95
Static Decay 0.0100 - 20.0 sec0.0100 - 20.0 secAverage value: 2.02 sec Grade Count:11
Dielectric Constant 2.20 - 2.382.20 - 2.38Average value: 2.30 Grade Count:63
Dielectric Strength 19.7 - 140 kV/mm500 - 3560 kV/inAverage value: 128 kV/mm Grade Count:65
Dissipation Factor 0.0000700 - 0.003000.0000700 - 0.00300Average value: 0.000410 Grade Count:61
Arc Resistance 88.0 - 136 sec88.0 - 136 secAverage value: 104 sec Grade Count:3
Comparative Tracking Index 600 V600 VAverage value: 600 V Grade Count:76
Tribocharge 10.0 V10.0 VAverage value: 10.0 V Grade Count:3
 
Thermal PropertiesMetricEnglishComments
CTE, linear 18.0 - 185 µm/m-°C10.0 - 103 µin/in-°FAverage value: 114 µm/m-°C Grade Count:106
Melting Point 61.0 - 180 °C142 - 356 °FAverage value: 160 °C Grade Count:199
Crystallization Temperature 110 - 115 °C230 - 239 °FAverage value: 111 °C Grade Count:5
Maximum Service Temperature, Air 65.0 - 125 °C149 - 257 °FAverage value: 78.3 °C Grade Count:26
Deflection Temperature at 0.46 MPa (66 psi) 55.0 - 266 °C131 - 511 °FAverage value: 102 °C Grade Count:634
Deflection Temperature at 1.8 MPa (264 psi) 37.0 - 172 °C98.6 - 341 °FAverage value: 64.1 °C Grade Count:250
Vicat Softening Point 35.0 - 158 °C95.0 - 316 °FAverage value: 120 °C Grade Count:282
Heat Distortion Temperature 85.0 - 115 °C185 - 239 °FAverage value: 97.5 °C Grade Count:8
Minimum Service Temperature, Air -30.0 °C-22.0 °FAverage value: -30.0 °C Grade Count:5
Brittleness Temperature -20.0 °C-4.00 °FAverage value: -20.0 °C Grade Count:16
UL RTI, Electrical 65.0 - 221 °C149 - 430 °FAverage value: 147 °C Grade Count:5
UL RTI, Mechanical with Impact 65.0 - 221 °C149 - 430 °FAverage value: 147 °C Grade Count:5
UL RTI, Mechanical without Impact 65.0 - 221 °C149 - 430 °FAverage value: 147 °C Grade Count:5
Flammability, UL94 HB - V-0HB - V-0Grade Count:81
Oxygen Index 24.0 - 30.0 %24.0 - 30.0 %Average value: 26.3 % Grade Count:6
Shrinkage 1.05 - 2.00 %1.05 - 2.00 %Average value: 1.36 % Grade Count:23
 
Optical PropertiesMetricEnglishComments
Haze 0.200 - 91.0 %0.200 - 91.0 %Average value: 34.4 % Grade Count:55
Gloss 30.0 - 160 %30.0 - 160 %Average value: 65.3 % Grade Count:20
Yellow Index 0.000300 - 2.44 %0.000300 - 2.44 %Average value: 0.669 % Grade Count:6
Transmission, Visible 84.0 - 90.0 %84.0 - 90.0 %Average value: 89.6 % Grade Count:25
 
Processing PropertiesMetricEnglishComments
Processing Temperature 87.8 - 274 °C190 - 525 °FAverage value: 208 °C Grade Count:41
Nozzle Temperature 204 - 235 °C400 - 455 °FAverage value: 212 °C Grade Count:10
Melt Temperature 145 - 320 °C293 - 608 °FAverage value: 209 °C Grade Count:87
Mold Temperature 4.00 - 91.0 °C39.2 - 196 °FAverage value: 41.0 °C Grade Count:81
Roll Temperature 40.0 - 50.0 °C104 - 122 °FAverage value: 43.3 °C Grade Count:5
Drying Temperature 60.0 - 100 °C140 - 212 °FAverage value: 77.2 °C Grade Count:23
Dry Time 1.00 - 4.00 hour1.00 - 4.00 hourAverage value: 2.53 hour Grade Count:29
Moisture Content 0.0500 - 1.00 %0.0500 - 1.00 %Average value: 0.620 % Grade Count:15
Injection Pressure 2.76 - 103 MPa400 - 15000 psiAverage value: 58.9 MPa Grade Count:32
Hold Pressure 2.07 - 8.27 MPa300 - 1200 psiAverage value: 5.17 MPa Grade Count:6
Back Pressure 0.172 - 1.03 MPa24.9 - 150 psiAverage value: 0.603 MPa Grade Count:10
Shelf Life 12.0 Month12.0 MonthAverage value: 12.0 Month Grade Count:5

转载请注明: 转自中国塑胶原料之家 http://www.su-jiao.com/wuxingbiao/

本文链接: http://www.su-jiao.com/yuanliaoku/show-30744.html

免责声明: 本文 Overview of materials for Polypropylene, Molded 仅代表作者个人观点，中国塑胶原料之家无关。中国塑胶原料之家网所转载的内容，其版权均由原作者和资料提供方所拥有！如因作品版权问题需要处理，请与我们联络

该类别其他物性信息

塑胶原料之家，专业塑料网站、原料报价网站，免费发布塑胶供求信息。塑胶原料之家为您提供塑料供应、塑料求购、塑料行情、塑料展会、塑料原料资讯服务。

2008-2015 塑料|塑胶原料|物性表大全|UL黄卡|SGS报告查询|最新价格--塑胶原料之家

沪ICP备15027283号-4