Overview of materials for Thermoset Fluoroelastomer

Overview of materials for Thermoset Fluoroelastomer 物性表: Overview of materials for Thermoset Fluoroelastomer物性表及特性介绍,Overview of materials for Thermoset Fluoroelastomer注塑参数详情,如需Overview of materials for Thermoset Fluoroelastomer下载, 可到相关下载区下载
  • 密度 [g/cm3]: 0.9
  • 拉伸强度 [MPa]: 0.965
  • 弯曲强度 [MPa]: 0.016
  • 脆化温度 [℃]: -60.0
  • 透光率 [%]: 25.0
 
Physical PropertiesMetricEnglishComments
Density 0.900 - 3.80 g/cc0.0325 - 0.137 lb/in³Average value: 1.85 g/cc Grade Count:231
Oxygen Transmission 88.0 - 150 cc-mm/m²-24hr-atm224 - 381 cc-mil/100 in²-24hr-atmAverage value: 104 cc-mm/m²-24hr-atm Grade Count:42
Mooney Viscosity 3.00 - 200
@Temperature 100 - 150 °C
3.00 - 200
@Temperature 212 - 302 °F
Average value: 48.6 Grade Count:232
 
Mechanical PropertiesMetricEnglishComments
Hardness, Shore A 38.0 - 10038.0 - 100Average value: 75.2 Grade Count:450
 35.0 - 85.0
@Temperature 225 - 225 °C
35.0 - 85.0
@Temperature 437 - 437 °F
Average value: 86.0 Grade Count:1
 58.0 - 98.0
@Temperature 93.3 - 200 °C
58.0 - 98.0
@Temperature 200 - 392 °F
Average value: 86.0 Grade Count:11
 58.0 - 98.0
@Time 252000 - 3.60e+6 sec
58.0 - 98.0
@Time 70.0 - 1000 hour
Average value: 86.0 Grade Count:11
Hardness, Shore D 47.0 - 80.047.0 - 80.0Average value: 59.8 Grade Count:4
Hardness, Shore M 72.0 - 83.072.0 - 83.0Average value: 77.8 Grade Count:4
Tensile Strength, Ultimate 0.0160 - 27.0 MPa2.32 - 3920 psiAverage value: 13.7 MPa Grade Count:376
 17.24 - 20.68 MPa
@Temperature 225 - 225 °C
2500 - 2999 psi
@Temperature 437 - 437 °F
Average value: 17.8 MPa Grade Count:1
 8.40471 - 25.7933 MPa
@Temperature 93.3 - 275 °C
1219.00 - 3741.01 psi
@Temperature 200 - 527 °F
Average value: 17.8 MPa Grade Count:16
 8.40471 - 25.7933 MPa
@Time 86400 - 3.60e+6 sec
1219.00 - 3741.01 psi
@Time 24.0 - 1000 hour
Average value: 17.8 MPa Grade Count:16
Tensile Strength, Yield 0.965 - 23.0 MPa140 - 3340 psiAverage value: 9.31 MPa Grade Count:143
Elongation at Break 28.0 - 500 %28.0 - 500 %Average value: 194 % Grade Count:475
 150 - 160 %
@Temperature 225 - 225 °C
150 - 160 %
@Temperature 437 - 437 °F
Average value: 196 % Grade Count:1
 61.6 - 456.5 %
@Temperature 93.3 - 275 °C
61.6 - 456.5 %
@Temperature 200 - 527 °F
Average value: 196 % Grade Count:16
 61.6 - 456.5 %
@Time 86400 - 3.60e+6 sec
61.6 - 456.5 %
@Time 24.0 - 1000 hour
Average value: 196 % Grade Count:16
Modulus of Elasticity 0.000600 - 0.140 GPa0.0870 - 20.3 ksiAverage value: 0.00736 GPa Grade Count:313
Compressive Modulus 0.000300 - 0.0153 GPa0.0435 - 2.22 ksiAverage value: 0.00534 GPa Grade Count:4
Shear Modulus 0.00193 - 0.0243 GPa0.280 - 3.53 ksiAverage value: 0.00760 GPa Grade Count:19
 0.0430 - 0.0430 GPa
@Temperature -12.0 - -12.0 °C
6.24 - 6.24 ksi
@Temperature 10.4 - 10.4 °F
Average value: 0.0430 GPa Grade Count:2
Secant Modulus 0.00512 - 0.0685 GPa0.743 - 9.94 ksiAverage value: 0.0215 GPa Grade Count:19
Coefficient of Friction 0.500 - 1.160.500 - 1.16Average value: 0.791 Grade Count:51
Tear Strength Test 132 - 359132 - 359Average value: 232 Grade Count:21
Tear Strength 3.06 - 31.4 kN/m17.5 - 179 pliAverage value: 21.5 kN/m Grade Count:87
Taber Abrasion, mg/1000 Cycles 40.0 - 32540.0 - 325Average value: 184 Grade Count:5
Compression Set 5.00 - 69.0 %5.00 - 69.0 %Average value: 26.1 % Grade Count:183
 4.00 - 65.0 %
@Temperature 100 - 300 °C
4.00 - 65.0 %
@Temperature 212 - 572 °F
Average value: 23.5 % Grade Count:265
 6.35 - 91.0 %
@Temperature 93.3 - 316 °C
6.35 - 91.0 %
@Temperature 200 - 601 °F
Average value: 23.5 % Grade Count:74
 6.35 - 91.0 %
@Time 79200 - 1.21e+6 sec
6.35 - 91.0 %
@Time 22.0 - 336 hour
Average value: 23.5 % Grade Count:74
 
Electrical PropertiesMetricEnglishComments
Electrical Resistivity 0.00500 - 5.00e+17 ohm-cm0.00500 - 5.00e+17 ohm-cmAverage value: 4.06e+16 ohm-cm Grade Count:53
Shielding Effectiveness 70.0 - 113 dB70.0 - 113 dBAverage value: 98.3 dB Grade Count:3
Dielectric Constant 2.50 - 11.42.50 - 11.4Average value: 9.80 Grade Count:44
Dielectric Strength 2.60 - 25.0 kV/mm66.0 - 635 kV/inAverage value: 23.2 kV/mm Grade Count:50
Dissipation Factor 0.005000.00500Average value: 0.00500 Grade Count:4
 
Thermal PropertiesMetricEnglishComments
CTE, linear 140 - 570 µm/m-°C77.8 - 317 µin/in-°FAverage value: 227 µm/m-°C Grade Count:48
Specific Heat Capacity 1.65 - 1.67 J/g-°C0.394 - 0.399 BTU/lb-°FAverage value: 1.65 J/g-°C Grade Count:40
 0.945 - 1.053 J/g-°C
@Temperature 50.0 - 150 °C
0.226 - 0.2517 BTU/lb-°F
@Temperature 122 - 302 °F
Average value: 0.991 J/g-°C Grade Count:4
Thermal Conductivity 0.200 - 0.300 W/m-K1.39 - 2.08 BTU-in/hr-ft²-°FAverage value: 0.235 W/m-K Grade Count:40
 0.170 - 0.190 W/m-K
@Temperature 50.0 - 200 °C
1.18 - 1.32 BTU-in/hr-ft²-°F
@Temperature 122 - 392 °F
Average value: 0.180 W/m-K Grade Count:4
Maximum Service Temperature, Air 93.3 - 350 °C200 - 662 °FAverage value: 232 °C Grade Count:280
Minimum Service Temperature, Air -65.0 - 0.000 °C-85.0 - 32.0 °FAverage value: -19.7 °C Grade Count:253
Brittleness Temperature -60.0 - -6.00 °C-76.0 - 21.2 °FAverage value: -23.4 °C Grade Count:91
Glass Transition Temp, Tg -51.1 - 3.00 °C-60.0 - 37.4 °FAverage value: -16.6 °C Grade Count:125
Transformation Temperature -40.0 - -2.00 °C-40.0 - 28.4 °FAverage value: -10.5 °C Grade Count:10
Flash Point 15.6 - 400 °C60.1 - 752 °FAverage value: 323 °C Grade Count:93
Shrinkage -21.0 - 25.0 %-21.0 - 25.0 %Average value: -3.60 % Grade Count:4
 
Optical PropertiesMetricEnglishComments
Transmission, Visible 25.0 - 90.0 %25.0 - 90.0 %Average value: 35.8 % Grade Count:6
 
Processing PropertiesMetricEnglishComments
Processing Temperature 160 - 170 °C320 - 338 °FAverage value: 165 °C Grade Count:25
Cure Time 1.50 - 4320 min0.0250 - 72.0 hourAverage value: 324 min Grade Count:27
 10.0 - 10.0 min
@Temperature 121 - 121 °C
0.167 - 0.167 hour
@Temperature 250 - 250 °F
Average value: 10.0 min Grade Count:2
Shelf Life 12.0 - 240 Month12.0 - 240 MonthAverage value: 188 Month Grade Count:19
 
Component Elements PropertiesMetricEnglishComments
Fluorine, F 64.0 - 73.0 %64.0 - 73.0 %Average value: 67.0 % Grade Count:52

转载请注明: 转自中国塑胶原料之家 http://www.su-jiao.com/wuxingbiao/

本文链接: http://www.su-jiao.com/yuanliaoku/show-35603.html

免责声明: 本文 Overview of materials for Thermoset Fluoroelastomer 仅代表作者个人观点,中国塑胶原料之家无关。中国塑胶原料之家网所转载的内容,其版权均由原作者和资料提供方所拥有!如因作品版权问题需要处理,请与我们联络

塑胶原料之家,专业塑料网站、原料报价网站,免费发布塑胶供求信息。塑胶原料之家为您提供塑料供应、塑料求购、塑料行情、塑料展会、塑料原料资讯服务。

2008-2015 塑料|塑胶原料|物性表大全|UL黄卡|SGS报告查询|最新价格--塑胶原料之家

沪ICP备15027283号-4