Daikin POLYFLON M-112 PTFE Molding Powder, Fine Cut

Daikin POLYFLON M-112 PTFE Molding Powder, Fine Cut 物性表: Daikin POLYFLON M-112 PTFE Molding Powder, Fine Cut物性表及特性介绍,Daikin POLYFLON M-112 PTFE Molding Powder, Fine Cut注塑参数详情,如需Daikin POLYFLON M-112 PTFE Molding Powder, Fine Cut下载, 可到相关下载区下载
  • 弯曲模量 [MPa]: 0.490
 
Physical PropertiesMetricEnglishComments
Specific Gravity 2.13 - 2.22 g/cc2.13 - 2.22 g/ccASTM D792
Bulk Density 0.380 g/cc0.0137 lb/in³ASTM D894
Water Absorption 0.00 %
@Thickness 8.50 mm,
Time 86400 sec
0.00 %
@Thickness 0.335 in,
Time 24.0 hour
ASTM D570
Particle Size 40 µm40 µmLaser Method (Dry)
Viscosity 1.00e+13 - 1.00e+15 cP
@Temperature 340 - 380 °C
1.00e+13 - 1.00e+15 cP
@Temperature 644 - 716 °F
Melt viscosity
Linear Mold Shrinkage 0.020 - 0.050 cm/cm0.020 - 0.050 in/in
Deformation 5.0 %5.0 %6.7 MPa load, at 100°C, 24 hrs; ASTM D621
 7.0 %7.0 %13.7 MPa load, at 25°C, 24 hrs; ASTM D621
 
Mechanical PropertiesMetricEnglishComments
Hardness, Shore D 50 - 6550 - 65
Tensile Strength at Break 20.0 - 45.0 MPa2900 - 6530 psiASTM D638
Elongation at Break 200 - 450 %200 - 450 %ASTM D638
Tensile Modulus 0.392 GPa56.9 ksiASTM D638
Flexural Modulus 0.490 - 0.588 GPa71.1 - 85.3 ksiASTM D790
Compressive Strength 5.00 - 6.00 MPa
@Temperature 25.0 °C
725 - 870 psi
@Temperature 77.0 °F
1% deformation; ASTM D695
Izod Impact, Unnotched 1.60 J/cm3.00 ft-lb/inASTM D256
Coefficient of Friction 0.020 - 0.0380.020 - 0.038Non-lubricating
 0.020 - 0.03850.020 - 0.0385Lubricating
Coefficient of Friction, Static 0.0200.020Coated-steel surface
Taber Abrasion, mg/1000 Cycles <= 17.1<= 17.19.8 N load, cs-10 wheel
 
Electrical PropertiesMetricEnglishComments
Volume Resistivity <= 1.00e+18 ohm-cm<= 1.00e+18 ohm-cmASTM D257
Dielectric Constant  2.1
@Frequency 1000 Hz
2.1
@Frequency 1000 Hz
ASTM D150
 2.1
@Frequency 1e+6 Hz
2.1
@Frequency 1e+6 Hz
ASTM D150
Dielectric Strength 19.0 kV/mm
@Thickness 3.20 mm
483 kV/in
@Thickness 0.126 in
Short time; ASTM D149
Dissipation Factor  <= 0.000010
@Frequency 1000 Hz
<= 0.000010
@Frequency 1000 Hz
ASTM D150
 0.000020
@Frequency 1e+6 Hz
0.000020
@Frequency 1e+6 Hz
ASTM D150
 
Thermal PropertiesMetricEnglishComments
CTE, linear 100 µm/m-°C
@Temperature 23.0 - 60.0 °C
55.6 µin/in-°F
@Temperature 73.4 - 140 °F
ASTM D696
Thermal Conductivity 0.250 W/m-K1.74 BTU-in/hr-ft²-°FASTM C177
Melting Point 327 °C621 °F
Maximum Service Temperature, Air 260 °C500 °FContinuous use
Flammability, UL94 V-0V-0
Oxygen Index >= 95 %>= 95 %ASTM D2863
 
Descriptive Properties
Chemical ResistanceExcellent
Contact Angle110Angle to level
WeatherabilityExcellent

转载请注明: 转自中国塑胶原料之家 http://www.su-jiao.com/wuxingbiao/

本文链接: http://www.su-jiao.com/yuanliaoku/show-43672.html

免责声明: 本文 Daikin POLYFLON M-112 PTFE Molding Powder, Fine Cut 仅代表作者个人观点,中国塑胶原料之家无关。中国塑胶原料之家网所转载的内容,其版权均由原作者和资料提供方所拥有!如因作品版权问题需要处理,请与我们联络

塑胶原料之家,专业塑料网站、原料报价网站,免费发布塑胶供求信息。塑胶原料之家为您提供塑料供应、塑料求购、塑料行情、塑料展会、塑料原料资讯服务。

2008-2015 塑料|塑胶原料|物性表大全|UL黄卡|SGS报告查询|最新价格--塑胶原料之家

沪ICP备15027283号-4