Physical Properties | Metric | English | Comments | ||
---|---|---|---|---|---|
Bulk Density | 0.600 - 0.900 g/cc | 0.0217 - 0.0325 lb/in³ | |||
Density | 1.37 g/cc | 0.0495 lb/in³ | ISO 1183 | ||
Water Absorption | 0.40 % | 0.40 % | ISO 62 | ||
Moisture Absorption at Equilibrium | 0.20 % | 0.20 % | ISO 62 | ||
Viscosity Measurement | 115 | 115 | [cm3/g]; ISO 307 | ||
Linear Mold Shrinkage, Flow | 0.0070 cm/cm | 0.0070 in/in | plate with film gate 150x150x3mm3 | ||
0.0122 cm/cm | 0.0122 in/in | ISO 2577 | |||
Linear Mold Shrinkage, Transverse | 0.0134 cm/cm | 0.0134 in/in | plate with film gate 150x150x3mm3 | ||
0.0138 cm/cm | 0.0138 in/in | ISO 2577 | |||
Melt Flow | 21.92 g/10 min @Load 2.16 kg, Temperature 250 °C |
21.92 g/10 min @Load 4.76 lb, Temperature 482 °F |
ISO 1133 | ||
Mechanical Properties | Metric | English | Comments | ||
Ball Indentation Hardness | 160 MPa @Load 98.0 kg, Time 30.0 sec |
23200 psi @Load 216 lb, Time 0.00833 hour |
ISO 2039-1 | ||
Tensile Strength at Break | 85.0 MPa | 12300 psi | ISO 527-1/-2 | ||
Elongation at Break | 4.5 % | 4.5 % | ISO 524-1/-2 | ||
Tensile Modulus | 4.50 GPa | 653 ksi | ISO 527-1-2 | ||
Flexural Strength | 140 MPa | 20300 psi | ISO 178 | ||
Charpy Impact Unnotched | 3.80 J/cm² @Temperature -30.0 °C |
18.1 ft-lb/in² @Temperature -22.0 °F |
ISO 179/1eU | ||
4.00 J/cm² @Temperature 23.0 °C |
19.0 ft-lb/in² @Temperature 73.4 °F |
ISO 179/1eU | |||
Charpy Impact, Notched | 0.400 J/cm² @Temperature 23.0 °C |
1.90 ft-lb/in² @Temperature 73.4 °F |
ISO 179/1eA | ||
Electrical Properties | Metric | English | Comments | ||
Volume Resistivity | 1.00e+14 ohm-cm | 1.00e+14 ohm-cm | IEC 60093 | ||
Dielectric Constant | 3.6 @Frequency 1.00e+6 Hz |
3.6 @Frequency 1.00e+6 Hz |
IEC 60250 | ||
3.6 @Frequency 100 Hz |
3.6 @Frequency 100 Hz |
IEC 60250 | |||
Dissipation Factor | 0.0012 @Frequency 100 Hz |
0.0012 @Frequency 100 Hz |
IEC 60250 | ||
0.015 @Frequency 1.00e+6 Hz |
0.015 @Frequency 1.00e+6 Hz |
IEC 60250 | |||
Comparative Tracking Index | 125 V | 125 V | Test Solution B; IEC 60112 | ||
300 V | 300 V | Test Solution A; IEC 60112 | |||
Thermal Properties | Metric | English | Comments | ||
CTE, linear, Parallel to Flow | 40.0 - 50.0 µm/m-°C @Temperature 23.0 - 80.0 °C |
22.2 - 27.8 µin/in-°F @Temperature 73.4 - 176 °F |
ISO 11359-1/-2 | ||
Thermal Conductivity | 0.230 W/m-K | 1.60 BTU-in/hr-ft²-°F | DIN 52612-1 | ||
Melting Point | 223 °C | 433 °F | ISO 11357-1/-2 | ||
Maximum Service Temperature, Air | 210 °C | 410 °F | |||
Deflection Temperature at 0.46 MPa (66 psi) | 220 °C | 428 °F | ISO 75-1/-2 | ||
Deflection Temperature at 1.8 MPa (264 psi) | 200 °C | 392 °F | ISO 75-1/-2 | ||
Decomposition Temperature | >= 290 °C | >= 554 °F | |||
Flammability, UL94 | HB @Thickness >=0.400 mm |
HB @Thickness >=0.0157 in |
IEC 60695-11-10 | ||
HB @Thickness >=4.00 mm |
HB @Thickness >=0.157 in |
by electrical sources of ignition, Method BH; IEC 60707 | |||
HB @Thickness 1.60 mm |
HB @Thickness 0.0630 in |
IEC 60695-11-10 | |||
Processing Properties | Metric | English | Comments | ||
Melt Temperature | 250 - 270 °C | 482 - 518 °F | Injection molding/Extrusion | ||
Mold Temperature | 60.0 - 100 °C | 140 - 212 °F | Injection molding | ||
De |
|||||
Commercial Status | Europe | ||||
Ignition Temperature | 350°C | ASTM D1929 |
上海松翰塑化科技有限公司!本公司承诺,假一赔百!所有产品都是原厂家,原包装一线独家营销!
我司所销售所有产品均为原厂原包,均可提供相关资料报告(如:物性表,MSDS报告,UL报告,COA报告,SGS报告,FDA等)!
欢迎新老客户来电或QQ咨询:
联系人:李先生
联系电话;13636696005
联系QQ;1020580970
联系邮箱;1020580970@qq.com