Physical Properties | Metric | English | Comments | ||
---|---|---|---|---|---|
Density | 1.25 g/cc | 0.0452 lb/in³ | |||
Filler Content | 20 % | 20 % | |||
Water Absorption | 0.22 % | 0.22 % | 24 hrs., 50% RH | ||
Linear Mold Shrinkage, Flow | 0.0030 - 0.0060 cm/cm | 0.0030 - 0.0060 in/in | |||
Linear Mold Shrinkage, Transverse | 0.0050 - 0.0080 cm/cm | 0.0050 - 0.0080 in/in | |||
Mechanical Properties | Metric | English | Comments | ||
Tensile Strength at Break | 150 MPa | 21800 psi | |||
Elongation at Break | 2.9 % | 2.9 % | |||
Tensile Modulus | 7.30 GPa | 1060 ksi | |||
Flexural Yield Strength | 215 MPa | 31200 psi | |||
Flexural Modulus | 6.70 GPa | 972 ksi | |||
Izod Impact, Notched (ISO) | 8.00 kJ/m² | 3.81 ft-lb/in² | |||
Izod Impact, Unnotched (ISO) | 45.0 kJ/m² | 21.4 ft-lb/in² | |||
Charpy Impact Unnotched | 5.50 J/cm² | 26.2 ft-lb/in² | |||
Charpy Impact, Notched | 0.900 J/cm² | 4.28 ft-lb/in² | |||
Electrical Properties | Metric | English | Comments | ||
Electrical Resistivity | 3.10e+15 ohm-cm | 3.10e+15 ohm-cm | |||
Dielectric Constant | 3.1 | 3.1 | |||
Dielectric Strength | 25.0 kV/mm | 635 kV/in | ASTM D145 | ||
Dissipation Factor | 0.034 | 0.034 | IEC 60250 | ||
Arc Resistance | 120 - 180 sec | 120 - 180 sec | ASTM D495 | ||
Comparative Tracking Index | 400 - 600 V | 400 - 600 V | IEC 60112 | ||
Hot Wire Ignition, HWI | 0.00 - 7.0 sec @Thickness 1.50 mm |
0.00 - 7.0 sec @Thickness 0.0591 in |
UL 746A | ||
High Amp Arc Ignition, HAI | >= 120 arcs @Thickness 1.50 mm |
>= 120 arcs @Thickness 0.0591 in |
UL 746A | ||
Thermal Properties | Metric | English | Comments | ||
CTE, linear, Parallel to Flow | 30.0 µm/m-°C @Temperature -30.0 - 30.0 °C |
16.7 µin/in-°F @Temperature -22.0 - 86.0 °F |
|||
CTE, linear, Transverse to Flow | 54.0 µm/m-°C | 30.0 µin/in-°F | |||
Deflection Temperature at 0.46 MPa (66 psi) | 240 °C | 464 °F | |||
Deflection Temperature at 1.8 MPa (264 psi) | 260 °C | 500 °F | |||
UL RTI, Electrical | 50.0 °C | 122 °F | UL746B | ||
UL RTI, Mechanical with Impact | 50.0 °C | 122 °F | UL746B | ||
UL RTI, Mechanical without Impact | 50.0 °C | 122 °F | UL746B | ||
Flammability, UL94 | HB @Thickness 0.750 mm |
HB @Thickness 0.0295 in |
|||
Processing Properties | Metric | English | Comments | ||
Melt Temperature | 280 - 310 °C | 536 - 590 °F | |||
Mold Temperature | 50.0 - 80.0 °C | 122 - 176 °F | |||
Drying Temperature | 80.0 °C | 176 °F | 1 - 3 hrs | ||
De |
|||||
Comments | High Ductility | ||||
Nylon/SPS blend |
.
上海松翰塑化科技有限公司!本公司承诺,假一赔百!所有产品都是原厂家,原包装一线独家营销!
我司所销售所有产品均为原厂原包,均可提供相关资料报告(如:物性表,MSDS报告,UL报告,COA报告,SGS报告,FDA等)!
欢迎新老客户来电或QQ咨询:
联系人:李生
联系电话;13636696005
联系QQ;1020580970
联系邮箱;1020580970@qq.com