- 密度 [g/cm3]: 1.19
- 吸水率 [%]: 0.2
- 缺口冲击强度: 0.22
- 断裂伸长率 [%]: 114
- 弯曲强度 [MPa]: 69.0
- 弯曲模量 [MPa]: 3.30
- 透光率 [%]: 92.0
| Physical Properties | Metric | English | Comments |
|---|---|---|---|
| Density | 1.19 g/cc | 0.0430 lb/in³ | ASTM D792 |
| Water Absorption | 0.20 % | 0.20 % | 24 hrs, 23°C; ASTM D570 |
| Water Absorption at Saturation | 1.1 % | 1.1 % | 48 days immersion |
| Mechanical Properties | Metric | English | Comments |
| Hardness, Barcol | 49 | 49 | ASTM D2583 |
| Hardness, Rockwell M | 94 | 94 | ASTM D785 |
| Tensile Strength, Ultimate | 69.0 MPa | 10000 psi | ASTM D638 |
| Elongation at Break | 4.2 % | 4.2 % | ASTM D638 |
| Tensile Modulus | 2.80 GPa | 406 ksi | ASTM D638 |
| Flexural Yield Strength | 114 MPa | 16500 psi | ASTM D790 |
| Flexural Modulus | 3.30 GPa | 479 ksi | ASTM D790 |
| Compressive Yield Strength | 124 MPa | 18000 psi | ASTM D695 |
| Izod Impact, Notched | 0.220 J/cm | 0.412 ft-lb/in | ASTM D256 |
| Electrical Properties | Metric | English | Comments |
| Electrical Resistivity | 1.60e+16 ohm-cm | 1.60e+16 ohm-cm | ASTM D257 |
| Surface Resistance | 1.90e+15 ohm | 1.90e+15 ohm | ASTM D257 |
| Dielectric Constant | 2.7 @Frequency 1e+6 Hz | 2.7 @Frequency 1e+6 Hz | ASTM D150 |
| 3.5 @Frequency 60 Hz | 3.5 @Frequency 60 Hz | ASTM D150 | |
| Dielectric Strength | 17.0 kV/mm @Thickness 3.20 mm | 432 kV/in @Thickness 0.126 in | Short time; ASTM D149 |
| Dissipation Factor | 0.020 @Frequency 1e+6 Hz | 0.020 @Frequency 1e+6 Hz | ASTM D150 |
| 0.060 @Frequency 60 Hz | 0.060 @Frequency 60 Hz | ASTM D150 | |
| Thermal Properties | Metric | English | Comments |
| CTE, linear | 61.0 µm/m-°C @Temperature 20.0 °C | 33.9 µin/in-°F @Temperature 68.0 °F | ASTM D696 |
| Specific Heat Capacity | 1.47 J/g-°C | 0.351 BTU/lb-°F | |
| Thermal Conductivity | 0.190 W/m-K | 1.32 BTU-in/hr-ft²-°F | Cenco-Fitch test |
| Maximum Service Temperature, Air | 82.0 °C | 180 °F | Continuous service temperature |
| 93.0 °C | 199 °F | Short-term | |
| Deflection Temperature at 1.8 MPa (264 psi) | 99.0 °C | 210 °F | ASTM D648 |
| Minimum Service Temperature, Air | -40.0 °C | -40.0 °F | |
| Optical Properties | Metric | English | Comments |
| Refractive Index | 1.49 | 1.49 | ASTM D542 |
| Haze | <= 1.0 % | <= 1.0 % | ASTM D1003 |
| Transmission, Visible | 92 % | 92 % | ASTM D1003 |
| Processing Properties | Metric | English | Comments |
| Processing Temperature | 171 - 193 °C | 340 - 379 °F | forming temperature |