Rogers Corporation Poron® 4701-41-20 Urethane Foam, Soft, Enhanced Sealability物性表参数

Rogers Corporation Poron® 4701-41-20 Urethane Foam, Soft, Enhanced Sealability

Rogers Corporation Poron® 4701-41-20 Urethane Foam, Soft, Enhanced Sealability 物性表: Rogers Corporation Poron® 4701-41-20 Urethane Foam, Soft, Enhanced Sealability物性表及特性介绍,Rogers Corporation Poron® 4701-41-20 Urethane Foam, Soft, Enhanced Sealability注塑参数详情,如需Rogers Corporation Poron® 4701-41-20 Urethane Foam, Soft, Enhanced Sealability下载, 可到相关下载区下载

密度 [g/cm3]: 0.32
吸水率 [%]: 13.0

Physical Properties	Metric	English	Comments

Density	0.320 g/cc	0.0116 lb/in³	ASTM D3574-95 Test A
Water Absorption	13 %	13 %	Immersion; ASTM D570-95
Moisture Absorption at Equilibrium	2.0 %	2.0 %	High Humidity; AMS 3568-95
Thickness	1570 - 3180 microns	62.0 - 125 mil	Range of Thicknesses Available
Outgassing - Total Mass Loss	0.040 % @Temperature 125 °C, Time 86400 sec	0.040 % @Temperature 257 °F, Time 24.0 hour	CVCM; at 7000 Pa; ASTM E595-93
	0.46 % @Temperature 125 °C, Time 86400 sec	0.46 % @Temperature 257 °F, Time 24.0 hour	WVR; at 7000 Pa; ASTM E595-93
	0.97 % @Temperature 125 °C, Time 86400 sec	0.97 % @Temperature 257 °F, Time 24.0 hour	TML; at 7000 Pa; ASTM E595-93

Mechanical Properties	Metric	English	Comments
Hardness, Shore O	24	24	ASTM D2240-97
Tensile Strength	>= 0.517 MPa	>= 75.0 psi	ASTM D3574-75 Test E
	0.607 MPa	88.0 psi	Typical; ASTM D3574-75 Test E
Elongation at Break	>= 100 %	>= 100 %	ASTM D3574-75 Test E
	140 %	140 %	Typical; ASTM D3574-75 Test E
Compressive Yield Strength	0.0689 - 0.117 MPa @Strain 25.0 %	10.0 - 17.0 psi @Strain 25.0 %	Range, 0.2"/min. strain rate
	0.103 MPa @Strain 25.0 %	15.0 psi @Strain 25.0 %	Typical value, 0.2"/min. strain rate
Tear Strength	>= 1.40 kN/m	>= 7.99 pli	ASTM D264-91 Die C
	2.30 kN/m	13.1 pli	Typical; ASTM D264-91 Die C
Compression Set	5.0 % @Temperature 23.0 °C	5.0 % @Temperature 73.4 °F	ASTM D1667-90 Test D
	5.0 % @Temperature 121 °C	5.0 % @Temperature 250 °F	autoclaved 5 hrs; ASTM D3574-95 J/Test D
	10 % @Temperature 70.0 °C	10 % @Temperature 158 °F	ASTM D3574-95 Test D

Electrical Properties	Metric	English	Comments
Volume Resistivity	1.00e+12 ohm-cm	1.00e+12 ohm-cm	ASTM D257-99
Dielectric Constant	1.71 @Time 86400 sec	1.71 @Time 24.0 hour	50% RH; ASTM D150
Dielectric Strength	1.97 kV/mm	50.0 kV/in	ASTM D149-97a
Dissipation Factor	0.050	0.050	ASTM D150-98

Thermal Properties	Metric	English	Comments
CTE, linear	230 - 310 µm/m-°C	128 - 172 µin/in-°F
Maximum Service Temperature, Air	90.0 °C	194 °F	Constant use; SAE J-2236
	121 °C	250 °F	Intermittent use; ASTM D746-98

关键词:
供应
聚氨酯TS
Soft
Enhanced Sealability
Rogers Corporation Poron® 4701-41-20 Urethane Foam

转载请注明: 转自中国塑胶原料之家 http://www.su-jiao.com/wuxingbiao/

本文链接: http://www.su-jiao.com/yuanliaoku/show-37514.html

免责声明: 本文 Rogers Corporation Poron® 4701-41-20 Urethane Foam, Soft, Enhanced Sealability 仅代表作者个人观点，中国塑胶原料之家无关。中国塑胶原料之家网所转载的内容，其版权均由原作者和资料提供方所拥有！如因作品版权问题需要处理，请与我们联络

该类别其他物性信息