- 成型收缩率 [%]: 0.001
- 缺口冲击强度: 0.686
- 弯曲模量 [MPa]: 6.86
- 硬度: 120.0
- 热变形温度 [℃]: 200.0
Physical Properties | Metric | English | Comments | ||
---|---|---|---|---|---|
Specific Gravity | 1.60 g/cc | 1.60 g/cc | ASTM D792 | ||
Moisture Absorption | 0.0300 % @Time 86400 sec | 0.0300 % @Time 24.0 hour | ASTM D570 | ||
Linear Mold Shrinkage | 0.0010 - 0.0030 cm/cm @Thickness 1.60 mm | 0.0010 - 0.0030 in/in @Thickness 0.0630 in | horizontal; ASTM D955 | ||
0.0030 - 0.0060 cm/cm @Thickness 1.60 mm | 0.0030 - 0.0060 in/in @Thickness 0.0630 in | vertical; ASTM D955 | |||
Mechanical Properties | Metric | English | Comments | ||
Hardness, Rockwell R | 120 | 120 | ASTM D785 | ||
Tensile Strength | 78.5 MPa | 11400 psi | ASTM D638 | ||
Elongation at Break | 2.3 % | 2.3 % | ASTM D638 | ||
Flexural Strength | 100 MPa | 14500 psi | ASTM D790 | ||
Flexural Modulus | 6.86 GPa | 996 ksi | ASTM D790 | ||
Izod Impact, Notched | >= 0.686 J/cm @Thickness 6.35 mm | >= 1.29 ft-lb/in @Thickness 0.250 in | ASTM D256 | ||
Electrical Properties | Metric | English | Comments | ||
Volume Resistivity | 1.00e+16 ohm-cm | 1.00e+16 ohm-cm | ASTM D257 | ||
Surface Resistance | 1.00e+13 ohm | 1.00e+13 ohm | ASTM D257 | ||
Dielectric Constant | 3.5 @Frequency 60.0 Hz | 3.5 @Frequency 60.0 Hz | ASTM D150 | ||
Dielectric Strength | 20.0 kV/mm @Thickness 2.00 mm | 508 kV/in @Thickness 0.0787 in | ASTM D149 | ||
Dissipation Factor | 0.0010 @Frequency 60.0 Hz | 0.0010 @Frequency 60.0 Hz | ASTM D150 | ||
Arc Resistance | 80 sec | 80 sec | ASTM D495 | ||
Thermal Properties | Metric | English | Comments | ||
Melting Point | 225 °C | 437 °F | DSC | ||
Deflection Temperature at 0.46 MPa (66 psi) | 200 °C | 392 °F | ASTM D648 | ||
Deflection Temperature at 1.8 MPa (264 psi) | 138 °C | 280 °F | ASTM D648 | ||
Flammability, UL94 | V-0 @Thickness 0.800 mm | V-0 @Thickness 0.0315 in | |||
Processing Properties | Metric | English | Comments | ||
Processing Temperature | 250 - 280 °C | 482 - 536 °F | |||
Nozzle Temperature | 270 - 280 °C | 518 - 536 °F | |||
Mold Temperature | 40.0 - 120 °C | 104 - 248 °F | suitable temperature 60-80°C | ||
Injection Pressure | 50.0 - 120 MPa | 7250 - 17400 psi | |||
Hold Pressure | 30.0 - 80.0 MPa | 4350 - 11600 psi | |||
Back Pressure | 0.000 - 0.300 MPa | 0.000 - 43.5 psi | |||
Screw Speed | 60 - 120 rpm | 60 - 120 rpm | to be chosen in such a way that plasticizing time is just within cooling time | ||
Descriptive Properties | |||||
Injection Rate | middle-fast |