- 密度 [g/cm3]: 0.955
- 缺口冲击强度: 18.0
- 拉伸强度 [MPa]: 24.0
- 弯曲模量 [MPa]: 0.900
| Physical Properties | Metric | English | Comments | ||
|---|---|---|---|---|---|
| Density | 0.955 g/cc | 0.0345 lb/in³ | ISO R 1183 | ||
| Moisture Absorption at Equilibrium | 0.00 % | 0.00 % | DIN 53473 | ||
| Water Absorption at Saturation | >= 0.10 % @Temperature 20.0 °C | >= 0.10 % @Temperature 68.0 °F | ISO R 62 | ||
| Mechanical Properties | Metric | English | Comments | ||
| Ball Indentation Hardness | 36.0 MPa | 5220 psi | Hc 30; ISO 2039; partially | ||
| Tensile Strength, Yield | 24.0 MPa | 3480 psi | ISO-DIS 527 | ||
| Creep Strength | 2.80 MPa | 406 psi | 1% elongation, 1000 h; DIN 53444 | ||
| 4.50 MPa | 653 psi | 2% elongation, 1000 h; DIN 53444 | |||
| Tensile Modulus | 1.00 GPa | 145 ksi | DIN 53457 | ||
| Flexural Strength | 31.0 MPa | 4500 psi | DIN 54352 | ||
| Flexural Modulus | 0.900 GPa | 131 ksi | DIN 53457 | ||
| Izod Impact, Notched (ISO) | 18.0 kJ/m² | 8.57 ft-lb/in² | DIN 53453 | ||
| Izod Impact Resistance | NB | NB | swinging hammer 0,1 DIN 51222; DIN 53453 | ||
| Coefficient of Friction | 0.020 - 0.080 | 0.020 - 0.080 | With lubrication | ||
| Coefficient of Friction, Dynamic | 0.29 | 0.29 | no lube; Steel 2162, Rvst=2E-6m, p=0.05 Mpa, v=0.6 m/s, t=40°C | ||
| Tear Strength Test | >= 8.0 | >= 8.0 | ISO-DIS 527 | ||
| K Factor (Wear Factor) | 1.0e-9 | 1.0e-9 | |||
| Electrical Properties | Metric | English | Comments | ||
| Volume Resistivity | 1.00e+16 ohm-cm | 1.00e+16 ohm-cm | DIN 53482 | ||
| Dielectric Constant | 3.3 | 3.3 | DIN 53483 | ||
| Dielectric Strength | 50.0 kV/mm | 1270 kV/in | DIN 53481 | ||
| Dielectric Loss Index | 0.00020 | 0.00020 | DIN 53483 | ||
| Thermal Properties | Metric | English | Comments | ||
| CTE, linear | 200 µm/m-°C @Temperature 20.0 - 100 °C | 111 µin/in-°F @Temperature 68.0 - 212 °F | DIN 53752 | ||
| Specific Heat Capacity | 2.30 J/g-°C | 0.550 BTU/lb-°F | |||
| Thermal Conductivity | 0.140 W/m-K | 0.972 BTU-in/hr-ft²-°F | DIN 52612 | ||
| Melting Point | 130 °C | 266 °F | ISO R 1218 | ||
| Maximum Service Temperature, Air | 80.0 °C | 176 °F | Continuous | ||
| 120 °C | 248 °F | Intermittent | |||
| Minimum Service Temperature, Air | -100 °C | -148 °F | Continuous | ||
| Descriptive Properties | |||||
| Creepage/leakage Resistance | KA3b | DIN 53480 | |||