塑胶原料之家
  1. 首页
  2. 英文物性
  3. TPE
  4. Overview of materials for Styrenic Elastomer (TES)

Overview of materials for Styrenic Elastomer (TES)

Overview of materials for Styrenic Elastomer (TES) 物性表: Overview of materials for Styrenic Elastomer (TES)物性表及特性介绍,Overview of materials for Styrenic Elastomer (TES)注塑参数详情,如需Overview of materials for Styrenic Elastomer (TES)下载, 可到相关下载区下载
  • 熔体流动速率 [g/10min]: 0.1
  • 密度 [g/cm3]: 0.88
  • 吸水率 [%]: 0.05
  • 缺口冲击强度: 0.641
  • 拉伸强度 [MPa]: 0.207
  • 断裂伸长率 [%]: 2.66
  • 弯曲强度 [MPa]: 0.345
  • 弯曲模量 [MPa]: 0.00138
  • 脆化温度 [℃]: -65.0
  • 透光率 [%]: 82.0
 
Physical PropertiesMetricEnglishComments
Density 0.880 - 11.0 g/cc0.0318 - 0.397 lb/in³Average value: 1.06 g/cc Grade Count:909
Volatiles 0.400 - 0.750 %0.400 - 0.750 %Average value: 0.574 % Grade Count:19
Water Absorption 0.0500 %0.0500 %Average value: 0.0500 % Grade Count:10
Viscosity 0.0300 - 30000 cP0.0300 - 30000 cPAverage value: 5130 cP Grade Count:23
 1600 - 2300 cP
@Temperature 180 - 180 °C		1600 - 2300 cP
@Temperature 356 - 356 °F		Average value: 2080 cP Grade Count:4
Viscosity Measurement 4.00 - 57.0
@Temperature 150 - 180 °C		4.00 - 57.0
@Temperature 302 - 356 °F		Average value: 13.6 Grade Count:139
Viscosity Measure 6.00 - 80.0 cSt6.00 - 80.0 cStAverage value: 24.9 cSt Grade Count:15
Linear Mold Shrinkage 0.00300 - 0.0470 cm/cm0.00300 - 0.0470 in/inAverage value: 0.0183 cm/cm Grade Count:156
Linear Mold Shrinkage, Transverse 0.00100 - 0.0190 cm/cm0.00100 - 0.0190 in/inAverage value: 0.00861 cm/cm Grade Count:23
Melt Flow 0.100 - 57.0 g/10 min0.100 - 57.0 g/10 minAverage value: 8.67 g/10 min Grade Count:51
Deformation  30.0 - 64.0 %
@Temperature 700 - 700 °C		30.0 - 64.0 %
@Temperature 1290 - 1290 °F		Average value: 41.4 % Grade Count:8
 30.0 - 64.0 %
@Time 79200 - 79200 sec		30.0 - 64.0 %
@Time 22.0 - 22.0 hour		Average value: 41.4 % Grade Count:8
Ash 0.350 - 39.0 %0.350 - 39.0 %Average value: 15.0 % Grade Count:12
 
Chemical PropertiesMetricEnglishComments
Styrene Content 20.0 - 55.0 %20.0 - 55.0 %Average value: 31.9 % Grade Count:19
 
Mechanical PropertiesMetricEnglishComments
Hardness, Shore A 6.00 - 98.06.00 - 98.0Average value: 59.2 Grade Count:904
Hardness, Shore D 10.0 - 73.010.0 - 73.0Average value: 41.4 Grade Count:48
Tensile Strength, Ultimate 0.345 - 80.0 MPa50.0 - 11600 psiAverage value: 7.62 MPa Grade Count:822
Tensile Strength, Yield 0.207 - 20.0 MPa30.0 - 2900 psiAverage value: 3.90 MPa Grade Count:119
Elongation at Break 5.50 - 1900 %5.50 - 1900 %Average value: 601 % Grade Count:898
Modulus of Elasticity 0.000300 - 2.41 GPa0.0435 - 350 ksiAverage value: 0.0220 GPa Grade Count:203
Flexural Yield Strength 2.66 - 100 MPa386 - 14500 psiAverage value: 30.0 MPa Grade Count:5
Flexural Modulus 0.00138 - 2.55 GPa0.200 - 370 ksiAverage value: 0.649 GPa Grade Count:8
Rebound 22.0 - 65.0 %22.0 - 65.0 %Average value: 46.9 % Grade Count:27
Adhesive Bond Strength 0.550 - 2.65 MPa79.8 - 384 psiAverage value: 1.13 MPa Grade Count:10
Izod Impact, Notched 0.641 - 5340 J/cm1.20 - 10000 ft-lb/inAverage value: 2.39 J/cm Grade Count:24
Izod Impact, Unnotched 1.60 - 5340 J/cm3.00 - 10000 ft-lb/inAverage value: 6.01 J/cm Grade Count:23
Penetration 50.050.0Average value: 50.0 Grade Count:4
Tear Strength 5.78 - 230 kN/m33.0 - 1310 pliAverage value: 29.1 kN/m Grade Count:545
Peel Strength 0.000 - 50.0 kN/m0.000 - 285 pliAverage value: 8.17 kN/m Grade Count:92
Graves Tear Strength 2.50 - 92.0 kN/m14.3 - 525 pliAverage value: 18.2 kN/m Grade Count:210
Taber Abrasion, mg/1000 Cycles 30.0 - 54030.0 - 540Average value: 184 Grade Count:26
Compression Set 7.00 - 90.0 %7.00 - 90.0 %Average value: 26.9 % Grade Count:513
 16.0 - 95.0 %
@Temperature 70.0 - 100 °C		16.0 - 95.0 %
@Temperature 158 - 212 °F		Average value: 56.2 % Grade Count:148
 16.0 - 99.0 %
@Temperature -25.0 - 158 °C		16.0 - 99.0 %
@Temperature -13.0 - 316 °F		Average value: 56.2 % Grade Count:320
 16.0 - 99.0 %
@Time 79200 - 605000 sec		16.0 - 99.0 %
@Time 22.0 - 168 hour		Average value: 56.2 % Grade Count:320
Tensile Set  33.0 - 95.0 %
@Temperature 70.0 - 70.0 °C		33.0 - 95.0 %
@Temperature 158 - 158 °F		Average value: 58.4 % Grade Count:15
 33.0 - 95.0 %
@Time 79200 - 79200 sec		33.0 - 95.0 %
@Time 22.0 - 22.0 hour		Average value: 58.4 % Grade Count:15
 
Electrical PropertiesMetricEnglishComments
Electrical Resistivity 0.0100 - 1.00e+16 ohm-cm0.0100 - 1.00e+16 ohm-cmAverage value: 2.42e+15 ohm-cm Grade Count:90
Surface Resistance 10.0 - 9.90e+12 ohm10.0 - 9.90e+12 ohmAverage value: 5.80e+11 ohm Grade Count:21
Static Decay 2.00 sec2.00 secAverage value: 2.00 sec Grade Count:13
Dielectric Constant 2.10 - 2.802.10 - 2.80Average value: 2.47 Grade Count:21
Dielectric Strength 24.0 - 50.0 kV/mm610 - 1270 kV/inAverage value: 29.7 kV/mm Grade Count:55
Dissipation Factor 0.000100 - 0.005100.000100 - 0.00510Average value: 0.00248 Grade Count:21
Comparative Tracking Index 550 - 600 V550 - 600 VAverage value: 564 V Grade Count:21
 
Thermal PropertiesMetricEnglishComments
Maximum Service Temperature, Air 50.0 - 170 °C122 - 338 °FAverage value: 92.3 °C Grade Count:290
Minimum Service Temperature, Air -60.0 - -30.0 °C-76.0 - -22.0 °FAverage value: -46.4 °C Grade Count:309
Brittleness Temperature -65.0 - -21.0 °C-85.0 - -5.80 °FAverage value: -59.2 °C Grade Count:37
Flammability, UL94 HB - V-0HB - V-0Grade Count:154
Flammability Test 37.0 - 54.037.0 - 54.0Average value: 45.2 Grade Count:15
Oxygen Index 27.0 %27.0 %Average value: 27.0 % Grade Count:4
Ring & Ball Softening Point 128 - 135 °C262 - 275 °FAverage value: 131 °C Grade Count:4
 
Optical PropertiesMetricEnglishComments
Haze 3.70 - 15.0 %3.70 - 15.0 %Average value: 9.16 % Grade Count:21
Transmission, Visible 82.0 - 91.0 %82.0 - 91.0 %Average value: 89.9 % Grade Count:84
 
Processing PropertiesMetricEnglishComments
Processing Temperature 140 - 280 °C284 - 536 °FAverage value: 208 °C Grade Count:387
Nozzle Temperature 175 - 249 °C347 - 480 °FAverage value: 187 °C Grade Count:9
Die Temperature 140 - 249 °C284 - 480 °FAverage value: 191 °C Grade Count:3
Melt Temperature 149 - 371 °C300 - 700 °FAverage value: 195 °C Grade Count:109
Mold Temperature 10.0 - 149 °C50.0 - 300 °FAverage value: 44.5 °C Grade Count:252
Drying Temperature 51.7 - 135 °C125 - 275 °FAverage value: 75.0 °C Grade Count:248
Dry Time 2.00 - 80.0 hour2.00 - 80.0 hourAverage value: 3.83 hour Grade Count:116
Moisture Content 0.0300 - 0.150 %0.0300 - 0.150 %Average value: 0.0437 % Grade Count:68
Dew Point -31.7 - -17.8 °C-25.0 - 0.000 °FAverage value: -18.1 °C Grade Count:42
Injection Pressure 1.38 - 138 MPa200 - 20000 psiAverage value: 76.1 MPa Grade Count:91
Back Pressure 0.172 - 0.689 MPa25.0 - 100 psiAverage value: 0.349 MPa Grade Count:10
Screw Speed 25.0 - 100 rpm25.0 - 100 rpmAverage value: 52.5 rpm Grade Count:10

转载请注明: 转自中国塑胶原料之家 http://www.su-jiao.com/wuxingbiao/

本文链接: http://www.su-jiao.com/yuanliaoku/show-48092.html

免责声明: 本文 Overview of materials for Styrenic Elastomer (TES) 仅代表作者个人观点，中国塑胶原料之家无关。中国塑胶原料之家网所转载的内容，其版权均由原作者和资料提供方所拥有！如因作品版权问题需要处理，请与我们联络

该类别其他物性信息

塑胶原料之家，专业塑料网站、原料报价网站，免费发布塑胶供求信息。塑胶原料之家为您提供塑料供应、塑料求购、塑料行情、塑料展会、塑料原料资讯服务。

2008-2015 塑料|塑胶原料|物性表大全|UL黄卡|SGS报告查询|最新价格--塑胶原料之家

沪ICP备15027283号-4