赢创冷冻聚丙烯酸酯塑料®S-10丙烯酸酯复合成型
类别：聚合物；热塑性塑料；丙烯酸（有机玻璃）；丙烯酸，一般用途
材料说明：通过冷冻行业提供的数据
用途：汽车眼镜，板材，照明面板，和家居用品
物性表：
| Physical Properties | Metric | English | Comments |
|---|---|---|---|
| Density | 1.19 g/cc | 0.0430 lb/in³ | ASTM D792 |
| Water Absorption | <= 0.30 % | <= 0.30 % | ASTM D570 |
| Linear Mold Shrinkage | 0.0040 - 0.0070 cm/cm | 0.0040 - 0.0070 in/in | ASTM D551 |
| Melt Flow | 3.4 g/10 min @Load 3.80 kg, Temperature 230 °C |
3.4 g/10 min @Load 8.38 lb, Temperature 446 °F |
ASTM D1238 |
| Mechanical Properties | Metric | English | Comments |
| Hardness, Rockwell M | 95 | 95 | ASTM D785 |
| Tensile Strength, Ultimate | 78.0 MPa | 11300 psi | ASTM D638 |
| Elongation at Break | 4.0 - 6.0 % | 4.0 - 6.0 % | ASTM D638 |
| Elongation at Yield | 4.0 - 6.0 % | 4.0 - 6.0 % | ASTM D638 |
| Tensile Modulus | 3.20 GPa | 464 ksi | ASTM D638 |
| Flexural Yield Strength | 112 MPa | 16200 psi | ASTM D790 |
| Flexural Modulus | 3.50 GPa | 508 ksi | ASTM D790 |
| Compressive Yield Strength | 117 MPa | 17000 psi | ASTM D695 |
| Shear Modulus | 1.40 GPa | 203 ksi | |
| Electrical Properties | Metric | English | Comments |
Dielectric Constant  |
2.8 @Frequency 10000 Hz |
2.8 @Frequency 10000 Hz |
ASTM D150 |
| 3.7 @Frequency 100 Hz |
3.7 @Frequency 100 Hz |
ASTM D150 | |
| Dielectric Strength | 20.0 kV/mm @Thickness 3.00 mm |
508 kV/in @Thickness 0.118 in |
ASTM D149 |
| Thermal Properties | Metric | English | Comments |
| CTE, linear | 72.0 µm/m-°C @Temperature 0.000 - 100 °C |
40.0 µin/in-°F @Temperature 32.0 - 212 °F |
|
| Specific Heat Capacity | 1.47 J/g-°C | 0.351 BTU/lb-°F | typical of Acrylite® sheet |
| Thermal Conductivity | 0.190 W/m-K | 1.32 BTU-in/hr-ft²-°F | typical of Acrylite® sheet |
| Deflection Temperature at 1.8 MPa (264 psi) | 100 °C | 212 °F | Annealed; ASTM D648 |
| Vicat Softening Point | 117 °C | 243 °F | ASTM D1525 |
| Flammability, UL94 | HB | HB | |
| Optical Properties | Metric | English | Comments |
| Refractive Index | 1.49 | 1.49 | ASTM D542 |
| Haze | <= 1.0 % | <= 1.0 % | ASTM D1003 |
| Transmission, Visible | 92 % | 92 % | ASTM D1003 |
| Processing Properties | Metric | English | Comments |
| Processing Temperature | 240 - 265 °C | 464 - 509 °F | Inj. Molding cylinder temperature range |
上海松翰塑化科技有限公司！本公司承诺，假一赔百！所有产品都是原厂家，原包装一线独家营销！
欢迎新老客户来电咨询;
联系人：李先生
联系电话；13636696005
联系QQ；1396427082
联系邮箱；1396427082@qq.com
欢迎新老客户来电咨询;
联系人：李先生
联系电话；13636696005
联系QQ；1396427082
联系邮箱；1396427082@qq.com