Physical Properties | Metric | English | Comments | ||
---|---|---|---|---|---|
Density | 1.42 g/cc | 0.0513 lb/in³ | |||
Filler Content | 30 % | 30 % | |||
Water Absorption | 0.010 % | 0.010 % | 24 hrs., 50% RH | ||
Linear Mold Shrinkage, Flow | 0.0010 - 0.0030 cm/cm | 0.0010 - 0.0030 in/in | |||
Linear Mold Shrinkage, Transverse | 0.0030 - 0.0070 cm/cm | 0.0030 - 0.0070 in/in | |||
Mechanical Properties | Metric | English | Comments | ||
Tensile Strength at Break | 120 MPa | 17400 psi | |||
Elongation at Break | 2.0 % | 2.0 % | |||
Tensile Modulus | 11.6 GPa | 1680 ksi | |||
Flexural Yield Strength | 185 MPa | 26800 psi | |||
Flexural Modulus | 10.9 GPa | 1580 ksi | |||
Izod Impact, Notched (ISO) | 10.0 kJ/m² | 4.76 ft-lb/in² | |||
Izod Impact, Unnotched (ISO) | 28.0 kJ/m² | 13.3 ft-lb/in² | |||
Charpy Impact Unnotched | 3.20 J/cm² | 15.2 ft-lb/in² | |||
Charpy Impact, Notched | 1.00 J/cm² | 4.76 ft-lb/in² | |||
Electrical Properties | Metric | English | Comments | ||
Electrical Resistivity | 1.00e+16 ohm-cm | 1.00e+16 ohm-cm | |||
Dielectric Constant | 3.2 | 3.2 | |||
Dielectric Strength | 32.0 kV/mm | 813 kV/in | ASTM D145 | ||
Dissipation Factor | 0.0020 | 0.0020 | IEC 60250 | ||
Arc Resistance | 60 - 120 sec | 60 - 120 sec | ASTM D495 | ||
Comparative Tracking Index | 250 - 400 V | 250 - 400 V | IEC 60112 | ||
Hot Wire Ignition, HWI | 30 - 60 sec @Thickness 1.50 mm |
30 - 60 sec @Thickness 0.0591 in |
UL 746A | ||
High Amp Arc Ignition, HAI | >= 120 arcs @Thickness 1.50 mm |
>= 120 arcs @Thickness 0.0591 in |
UL 746A | ||
High Voltage Arc-Tracking Rate, HVTR | >= 150 mm/min | >= 5.91 in/min | UL746A | ||
Thermal Properties | Metric | English | Comments | ||
CTE, linear, Parallel to Flow | 15.0 µm/m-°C @Temperature -30.0 - 30.0 °C |
8.33 µin/in-°F @Temperature -22.0 - 86.0 °F |
|||
CTE, linear, Transverse to Flow | 47.0 µm/m-°C | 26.1 µin/in-°F | |||
Deflection Temperature at 0.46 MPa (66 psi) | 265 °C | 509 °F | |||
Deflection Temperature at 1.8 MPa (264 psi) | 240 °C | 464 °F | |||
UL RTI, Electrical | 125 °C | 257 °F | UL746B | ||
UL RTI, Mechanical with Impact | 120 °C | 248 °F | UL746B | ||
UL RTI, Mechanical without Impact | 120 °C | 248 °F | UL746B | ||
Flammability, UL94 | V-0 @Thickness 0.750 mm |
V-0 @Thickness 0.0295 in |
|||
V-0 @Thickness 1.50 mm |
V-0 @Thickness 0.0591 in |
||||
5VA @Thickness 1.50 mm |
5VA @Thickness 0.0591 in |
||||
5VA @Thickness 2.30 mm |
5VA @Thickness 0.0906 in |
||||
Processing Properties | Metric | English | Comments | ||
Melt Temperature | 280 - 310 °C | 536 - 590 °F | |||
Mold Temperature | 50.0 - 80.0 °C | 122 - 176 °F | |||
130 - 155 °C | 266 - 311 °F | For optimal surface finish | |||
De |
|||||
Comments | ISO10993 | ||||
Thin wall V0 & 5VA |
.
上海松翰塑化科技有限公司!本公司承诺,假一赔百!所有产品都是原厂家,原包装一线独家营销!
我司所销售所有产品均为原厂原包,均可提供相关资料报告(如:物性表,MSDS报告,UL报告,COA报告,SGS报告,FDA等)!
欢迎新老客户来电或QQ咨询:
联系人:李生
联系电话;13636696005
联系QQ;1020580970
联系邮箱;1020580970@qq.com