- 熔体流动速率 [g/10min]: 10.0
- 密度 [g/cm3]: 1.5
- 吸水率 [%]: 0.1
- 缺口冲击强度: 1.07
- 弯曲模量 [MPa]: 8.50
- 热变形温度 [℃]: 210.0
Physical Properties | Metric | English | Comments | ||
---|---|---|---|---|---|
Specific Gravity | 1.50 g/cc | 1.50 g/cc | ASTM D792 | ||
Density | 1.50 g/cc | 0.0542 lb/in³ | ISO 1183 | ||
Water Absorption | 0.100 % | 0.100 % | 24hr immersion; ASTM D570 | ||
Linear Mold Shrinkage, Flow | 0.00400 - 0.00600 cm/cm | 0.00400 - 0.00600 in/in | ASTM D955 | ||
0.00400 - 0.00600 cm/cm | 0.00400 - 0.00600 in/in | ISO 294-4 | |||
Melt Flow | 10.0 g/10 min | 10.0 g/10 min | ASTM D1238 | ||
Mechanical Properties | Metric | English | Comments | ||
Hardness, Rockwell M | 73.0 | 73.0 | ISO 2039-2 | ||
Tensile Strength at Break | 120 MPa | 17400 psi | 5mm/min; ISO 527-2/1A | ||
121 MPa | 17500 psi | ASTM D638 | |||
Elongation at Break | 2.90 % | 2.90 % | 5mm/min; ISO 527-2/1A | ||
3.00 % @Temperature 22.8 °C | 3.00 % @Temperature 73.0 °F | ASTM D638 | |||
Tensile Modulus | 9.20 GPa | 1330 ksi | 1mm/min; ISO 527-2/1A | ||
Flexural Strength | 179 MPa | 26000 psi | ASTM D790 | ||
180 MPa | 26100 psi | ISO 178 | |||
Flexural Modulus | 8.50 GPa | 1230 ksi | ISO 178 | ||
8.27 GPa @Temperature 22.8 °C | 1200 ksi @Temperature 73.0 °F | ASTM D790 | |||
Izod Impact, Notched | 1.07 J/cm | 2.00 ft-lb/in | ASTM D256 | ||
Izod Impact, Notched (ISO) | 12.0 kJ/m² | 5.71 ft-lb/in² | ISO 180/1A | ||
Charpy Impact Unnotched | 6.00 J/cm² | 28.6 ft-lb/in² | ISO 179/1eU | ||
4.50 J/cm² @Temperature -30.0 °C | 21.4 ft-lb/in² @Temperature -22.0 °F | ISO 179/1eU | |||
Charpy Impact, Notched | 1.19 J/cm² | 5.66 ft-lb/in² | ISO 179/1eA | ||
1.10 J/cm² @Temperature -30.0 °C | 5.23 ft-lb/in² @Temperature -22.0 °F | ISO 179/1eA | |||
Electrical Properties | Metric | English | Comments | ||
Dielectric Strength | 19.3 kV/mm | 490 kV/in | short term; ASTM D149 | ||
Thermal Properties | Metric | English | Comments | ||
CTE, linear | 20.0 µm/m-°C | 11.1 µin/in-°F | ISO 11359-2 | ||
CTE, linear, Transverse to Flow | 87.0 µm/m-°C | 48.3 µin/in-°F | ISO 11359-2 | ||
Melting Point | 225 °C | 437 °F | 10°C/min; ISO 11357-1,-2,-3 | ||
225 °C | 437 °F | ASTM D3418 | |||
Deflection Temperature at 0.46 MPa (66 psi) | 210 °C | 410 °F | ISO 75-1, -2 | ||
223 °C | 433 °F | ASTM D648 | |||
Deflection Temperature at 1.8 MPa (264 psi) | 164 °C | 327 °F | ISO 75-1, -2 | ||
209 °C | 408 °F | ASTM D648 | |||
Flammability, UL94 | HB | HB | UL94 | ||
Processing Properties | Metric | English | Comments | ||
Processing Temperature | 20.0 - 50.0 °C | 68.0 - 122 °F | |||
65.0 - 93.0 °C | 149 - 199 °F | Cavity temperature | |||
Feed Temperature | 230 - 240 °C | 446 - 464 °F | |||
Rear Barrel Temperature | 230 - 240 °C | 446 - 464 °F | |||
Middle Barrel Temperature | 235 - 250 °C | 455 - 482 °F | |||
Front Barrel Temperature | 240 - 260 °C | 464 - 500 °F | |||
Nozzle Temperature | 250 - 260 °C | 482 - 500 °F | |||
Zone 1 | 230 - 240 °C | 446 - 464 °F | |||
Zone 2 | 235 - 250 °C | 455 - 482 °F | |||
Zone 3 | 235 - 250 °C | 455 - 482 °F | |||
Zone 4 | 240 - 260 °C | 464 - 500 °F | |||
Die Temperature | 250 - 260 °C | 482 - 500 °F | |||
Melt Temperature | 235 - 260 °C | 455 - 500 °F | |||
235 - 260 °C | 455 - 500 °F | ||||
260 °C | 500 °F | Injection molding; ISO 294 | |||
Mold Temperature | 65.6 - 93.3 °C | 150 - 200 °F | |||
82.0 °C | 180 °F | Injection molding; ISO 294 | |||
Injection Velocity | 300 mm/sec | 11.8 in/sec | ISO 294 | ||
Drying Temperature | 120 - 130 °C | 248 - 266 °F | |||
Dry Time | 4.00 hour | 4.00 hour | |||
Moisture Content | 0.0200 % | 0.0200 % | Necessary low maximum residual | ||
Hold Pressure | 48.0 MPa | 6960 psi | ISO 294 | ||
Back Pressure | 0.000 - 0.345 MPa | 0.000 - 50.0 psi | |||
Hot-Working Temperature | 250 - 260 °C | 482 - 500 °F | |||
Descriptive Properties | |||||
Injection molding | Yes | ||||
Injection speed | medium-fast | ||||
Longer pre-drying times/storage | lower the temperature to 100° C until processed. | <= 60 h | |||
Processing conditions | ISO 7792-2 | ||||
Processing Notes | Fast Injection Speed | ||||
Medium Screw Speed |