Quadrant EPP Fluorosint® 500 (CM), PTFE, synthetic mica-filled, compression molded (ASTM Product Dat

Quadrant EPP Fluorosint® 500 (CM), PTFE, synthetic mica-filled, compression molded (ASTM Product Dat 物性表: Quadrant EPP Fluorosint® 500 (CM), PTFE, synthetic mica-filled, compression molded (ASTM Product Dat物性表及特性介绍,Quadrant EPP Fluorosint® 500 (CM), PTFE, synthetic mica-filled, compression molded (ASTM Product Dat注塑参数详情,如需Quadrant EPP Fluorosint® 500 (CM), PTFE, synthetic mica-filled, compression molded (ASTM Product Dat下载, 可到相关下载区下载
  • 吸水率 [%]: 0.1
  • 缺口冲击强度: 0.481
  • 断裂伸长率 [%]: 15.2
  • 弯曲模量 [MPa]: 3.45
  • 硬度: 55.0
 
Physical PropertiesMetricEnglishComments
Specific Gravity 2.32 g/cc2.32 g/ccASTM D792
Water Absorption 0.10 %0.10 %Immersion, 24hr; ASTM D570(2)
Water Absorption at Saturation 0.30 %0.30 %Immersion; ASTM D570(2)
Deformation 5.0 %5.0 %2000 psi; 122°F (50°C)
 
Mechanical PropertiesMetricEnglishComments
Hardness, Rockwell R 5555ASTM D785
Hardness, Shore D 7070ASTM D2240
Tensile Strength 7.58 MPa1100 psiASTM D638
Elongation at Break 30 %30 %ASTM D638
Tensile Modulus 2.07 GPa300 ksiASTM D638
Flexural Yield Strength 15.2 MPa2200 psiASTM D790
Flexural Modulus 3.45 GPa500 ksiASTM D790
Compressive Strength 27.6 MPa4000 psi10% Def.; ASTM D695
Compressive Modulus 1.72 GPa250 ksiASTM D695
Shear Strength 14.5 MPa2100 psiASTM D732
Izod Impact, Notched 0.481 J/cm0.900 ft-lb/inASTM D256 Type A
Coefficient of Friction 0.150.15Dry vs. Steel; QTM55007
K (wear) Factor 1210 x 10-8 mm³/N-M600 x 10-10 in³-min/ft-lb-hrQTM 55010
Limiting Pressure Velocity 0.280 MPa-m/sec8000 psi-ft/min4:1 safety factor; QTM 55007
 
Electrical PropertiesMetricEnglishComments
Surface Resistivity per Square >= 1.00e+13 ohm>= 1.00e+13 ohmEOS/ESD S11.11
Dielectric Constant 2.85
@Frequency 1e+6 Hz
2.85
@Frequency 1e+6 Hz
ASTM D150
Dielectric Strength 10.8 kV/mm275 kV/inShort Term; ASTM D149
Dissipation Factor 0.0080
@Frequency 1e+6 Hz
0.0080
@Frequency 1e+6 Hz
ASTM D150
 
Thermal PropertiesMetricEnglishComments
CTE, linear 45.0 µm/m-°C
@Temperature -40.0 - 149 °C
25.0 µin/in-°F
@Temperature -40.0 - 300 °F
ASTM E831
Thermal Conductivity 0.764 W/m-K5.30 BTU-in/hr-ft²-°FASTM F433
Melting Point 327 °C621 °FCrystalline, Peak; ASTM D3418
Maximum Service Temperature, Air 260 °C500 °FLong Term
Deflection Temperature at 1.8 MPa (264 psi) 132 °C270 °FASTM D648
Flammability, UL94 V-0V-01/8 inch (Estimated Rating)
 
Compliance PropertiesMetricEnglishComments
3A-Dairy NoNo
Canada AG NoNo
FDA NoNo
NSF NoNo
USDA NoNo
USP Class VI NoNo
 
Chemical Resistance PropertiesMetricEnglishComments
Acids, Strong (pH 1-3) AcceptableAcceptable
Acids, Weak AcceptableAcceptable
Alcohols AcceptableAcceptable
Alkalies, Strong (pH 11-14) UnacceptableUnacceptable
Alkalies, Weak AcceptableAcceptable
Chlorinated Solvents AcceptableAcceptable
Conductive / Static Dissipative NoNo
Continuous Sunlight AcceptableAcceptable
Hot Water / Steam LimitedLimited
Hydrocarbons - Aliphatic AcceptableAcceptable
Hydrocarbons - Aromatic AcceptableAcceptable
Inorganic Salt Solutions AcceptableAcceptable
Ketones, Esters AcceptableAcceptable
 
Descriptive Properties
ColorNatural
Machinability21-10, 1=Easier to Machine

转载请注明: 转自中国塑胶原料之家 http://www.su-jiao.com/wuxingbiao/

本文链接: http://www.su-jiao.com/yuanliaoku/show-43548.html

免责声明: 本文 Quadrant EPP Fluorosint® 500 (CM), PTFE, synthetic mica-filled, compression molded (ASTM Product Dat 仅代表作者个人观点,中国塑胶原料之家无关。中国塑胶原料之家网所转载的内容,其版权均由原作者和资料提供方所拥有!如因作品版权问题需要处理,请与我们联络

塑胶原料之家,专业塑料网站、原料报价网站,免费发布塑胶供求信息。塑胶原料之家为您提供塑料供应、塑料求购、塑料行情、塑料展会、塑料原料资讯服务。

2008-2015 塑料|塑胶原料|物性表大全|UL黄卡|SGS报告查询|最新价格--塑胶原料之家

沪ICP备15027283号-4