DSM Stanyl® TW241F10 Nylon 46-50% Glass Reinforced (European Grade) (Cond)物性表参数

DSM Stanyl® TW241F10 Nylon 46-50% Glass Reinforced (European Grade) (Cond)

DSM Stanyl® TW241F10 Nylon 46-50% Glass Reinforced (European Grade) (Cond) 物性表: DSM Stanyl® TW241F10 Nylon 46-50% Glass Reinforced (European Grade) (Cond)物性表及特性介绍,DSM Stanyl® TW241F10 Nylon 46-50% Glass Reinforced (European Grade) (Cond)注塑参数详情,如需DSM Stanyl® TW241F10 Nylon 46-50% Glass Reinforced (European Grade) (Cond)下载, 可到相关下载区下载

密度 [g/cm3]: 1.62
吸水率 [%]: 7.0

Physical Properties	Metric	English	Comments

Density	1.62 g/cc	0.0585 lb/in³	(DAM); ISO 1183
Water Absorption	7.0 %	7.0 %	DAM; Sim. to ISO 62
Moisture Absorption at Equilibrium	1.8 %	1.8 %	Humidity Absorption (DAM); Sim. to ISO 62
Linear Mold Shrinkage, Flow	0.0040 cm/cm	0.0040 in/in	DAM; ISO 294-4
	0.0090 cm/cm	0.0090 in/in	DAM; ISO 294-4

Mechanical Properties	Metric	English	Comments
Tensile Strength at Break	160 MPa	23200 psi	ISO 527-1/-2
Elongation at Break	5.0 %	5.0 %	ISO 527-1/-2
Tensile Modulus	10.0 GPa	1450 ksi	ISO 527-1/-2
Charpy Impact Unnotched	8.00 J/cm² @Temperature -30.0 °C	38.1 ft-lb/in² @Temperature -22.0 °F	ISO 179/1eU
	10.0 J/cm² @Temperature 23.0 °C	47.6 ft-lb/in² @Temperature 73.4 °F	ISO 179/1eU
Charpy Impact, Notched	1.40 J/cm² @Temperature -30.0 °C	6.66 ft-lb/in² @Temperature -22.0 °F	ISO 179/1eA
	2.40 J/cm² @Temperature 23.0 °C	11.4 ft-lb/in² @Temperature 73.4 °F	ISO 179/1eA
Tensile Creep Modulus, 1000 hours	9000 MPa	1.31e+6 psi	ISO 899-1

Electrical Properties	Metric	English	Comments
Volume Resistivity	1.00e+10 ohm-cm	1.00e+10 ohm-cm	IEC 60093
Surface Resistance	1.00e+13 ohm	1.00e+13 ohm	IEC 60093
Dielectric Constant	4.7 @Frequency 1e+6 Hz	4.7 @Frequency 1e+6 Hz	IEC 60250
	16 @Frequency 100 Hz	16 @Frequency 100 Hz	IEC 60250
Dielectric Strength	20.0 kV/mm	508 kV/in	IEC 60243-1
Dissipation Factor	0.010 @Frequency 1e+6 Hz	0.010 @Frequency 1e+6 Hz	IEC 60250
	0.060 @Frequency 100 Hz	0.060 @Frequency 100 Hz	IEC 60250
Comparative Tracking Index	300 V	300 V	IEC 60112

Thermal Properties	Metric	English	Comments
Melting Point	295 °C	563 °F	10°C/min (DAM); ISO 11357-1/-3

Descriptive Properties
Heat Stabilized or Stable to Heat	Yes
Injection Molding	Yes
Platable	Yes
With Fillers	Yes

关键词:
PA46
供应
DSM Stanyl® TW241F10 Nylon 46-50% Glass Reinforced (European Grade) (Cond)

转载请注明: 转自中国塑胶原料之家 http://www.su-jiao.com/wuxingbiao/

本文链接: http://www.su-jiao.com/yuanliaoku/show-44628.html

免责声明: 本文 DSM Stanyl® TW241F10 Nylon 46-50% Glass Reinforced (European Grade) (Cond) 仅代表作者个人观点，中国塑胶原料之家无关。中国塑胶原料之家网所转载的内容，其版权均由原作者和资料提供方所拥有！如因作品版权问题需要处理，请与我们联络