- 密度 [g/cm3]: 1.59
- 吸水率 [%]: 0.165
- 缺口冲击强度: 0.39
- 弯曲强度 [MPa]: 56.0
- 弯曲模量 [MPa]: 8.40
| Physical Properties | Metric | English | Comments |
|---|---|---|---|
| Bulk Density | 0.670 g/cc | 0.0242 lb/in³ | ASTM D1895 |
| Density | 1.59 g/cc | 0.0574 lb/in³ | ASTM D792 |
| Water Absorption | 0.165 % | 0.165 % | ASTM D570 |
| Linear Mold Shrinkage | 0.00233 cm/cm | 0.00233 in/in | ASTM D955 |
| Mechanical Properties | Metric | English | Comments |
| Hardness, Rockwell E | 43 | 43 | ASTM D785 |
| Tensile Strength, Ultimate | 56.0 MPa | 8120 psi | ASTM D638 |
| Elongation at Break | 0.75 % | 0.75 % | ASTM D638 |
| Tensile Modulus | 9.60 GPa | 1390 ksi | ASTM D638 |
| Flexural Strength | 90.0 MPa | 13100 psi | ASTM D790 |
| Flexural Modulus | 8.40 GPa | 1220 ksi | ASTM D790 |
| Compressive Strength | 116 MPa | 16800 psi | ASTM D695 |
| Izod Impact, Notched | 0.390 J/cm | 0.731 ft-lb/in | ASTM D256 |
| Charpy Impact, Notched | 0.340 J/cm² | 1.62 ft-lb/in² | ASTM D256 |
| Impact | 292 | 292 | J/m drop Ball Impact; PLENCO |
| Electrical Properties | Metric | English | Comments |
| Volume Resistivity | 6.40e+11 ohm-cm | 6.40e+11 ohm-cm | ASTM D247 |
| Dielectric Constant | 5.5 | 5.5 | ASTM D150 |
| Dielectric Strength | 10.5 kV/mm | 267 kV/in | Step by Step; ASTM D149 |
| 12.9 kV/mm | 328 kV/in | Short Time; ASTM D149 | |
| Dissipation Factor | 0.083 | 0.083 | ASTM D150 |
| Arc Resistance | 135 sec | 135 sec | ASTM D495 |
| Comparative Tracking Index | 175 V | 175 V | ASTM D3638 |
| Thermal Properties | Metric | English | Comments |
| CTE, linear | 53.0 µm/m-°C @Temperature 40.0 - 130 °C | 29.4 µin/in-°F @Temperature 104 - 266 °F | TMA; ASTM E831 |
| Thermal Conductivity | 0.440 W/m-K @Temperature 100 °C | 3.05 BTU-in/hr-ft²-°F @Temperature 212 °F | ASTM E1461 |
| Maximum Service Temperature, Air | 244 °C | 471 °F | Heat Resistance; ASTM D570D |
| Deflection Temperature at 1.8 MPa (264 psi) | 232 °C | 450 °F | ASTM D648 |
| Flammability, UL94 | V-0 @Thickness 6.00 mm | V-0 @Thickness 0.236 in | |
| Oxygen Index | 36 % | 36 % | ASTM D2863 |
| Shrinkage | 0.128 % | 0.128 % | 72 hr, 120ºC; ASTM D1299 |