塑胶原料之家
  1. 首页
  2. 英文物性
  3. PA66
  4. Overview of materials for Nylon 66, Heat Stabilized

Overview of materials for Nylon 66, Heat Stabilized

Overview of materials for Nylon 66, Heat Stabilized 物性表: Overview of materials for Nylon 66, Heat Stabilized物性表及特性介绍,Overview of materials for Nylon 66, Heat Stabilized注塑参数详情,如需Overview of materials for Nylon 66, Heat Stabilized下载, 可到相关下载区下载
  • 熔体流动速率 [g/10min]: 1.0
  • 密度 [g/cm3]: 1.07
  • 吸水率 [%]: 0.3
  • 缺口冲击强度: 0.3
  • 拉伸强度 [MPa]: 10.3
  • 断裂伸长率 [%]: 27.6
  • 弯曲强度 [MPa]: 34.5
  • 弯曲模量 [MPa]: 0.255
  • 硬度: 82.0
  • 热变形温度 [℃]: 100.0
 
Physical PropertiesMetricEnglishComments
Density 1.07 - 1.85 g/cc0.0387 - 0.0668 lb/in³Average value: 1.32 g/cc Grade Count:313
Water Absorption 0.300 - 8.50 %0.300 - 8.50 %Average value: 1.08 % Grade Count:231
Moisture Absorption at Equilibrium 0.250 - 2.80 %0.250 - 2.80 %Average value: 1.95 % Grade Count:28
Water Absorption at Saturation 5.10 - 8.50 %5.10 - 8.50 %Average value: 7.85 % Grade Count:6
Viscosity Measurement 0.400 - 2400.400 - 240Average value: 51.1 Grade Count:8
Linear Mold Shrinkage 0.00100 - 0.0335 cm/cm0.00100 - 0.0335 in/inAverage value: 0.00819 cm/cm Grade Count:297
Linear Mold Shrinkage, Transverse 0.00480 - 0.0240 cm/cm0.00480 - 0.0240 in/inAverage value: 0.0107 cm/cm Grade Count:44
Melt Flow 1.00 - 5.00 g/10 min1.00 - 5.00 g/10 minAverage value: 2.83 g/10 min Grade Count:15
 
Mechanical PropertiesMetricEnglishComments
Hardness, Rockwell M 55.0 - 11955.0 - 119Average value: 79.4 Grade Count:31
Hardness, Rockwell R 82.0 - 12282.0 - 122Average value: 114 Grade Count:190
Tensile Strength, Ultimate 34.5 - 300 MPa5000 - 43500 psiAverage value: 104 MPa Grade Count:107
 30.0 - 55.0 MPa
@Temperature 60.0 - 120 °C		4350 - 7980 psi
@Temperature 140 - 248 °F		Average value: 38.8 MPa Grade Count:2
Tensile Strength, Yield 10.3 - 252 MPa1500 - 36500 psiAverage value: 123 MPa Grade Count:215
 144.79 - 144.79 MPa
@Temperature 93.3 - 93.3 °C		21000 - 21000 psi
@Temperature 200 - 200 °F		Average value: 145 MPa Grade Count:1
Elongation at Break 1.00 - 300 %1.00 - 300 %Average value: 23.2 % Grade Count:276
Elongation at Yield 3.00 - 90.0 %3.00 - 90.0 %Average value: 19.5 % Grade Count:32
Modulus of Elasticity 1.30 - 28.0 GPa189 - 4060 ksiAverage value: 7.95 GPa Grade Count:49
Flexural Yield Strength 27.6 - 420 MPa4000 - 60900 psiAverage value: 167 MPa Grade Count:285
 35.0 - 35.0 MPa
@Temperature 90.0 - 90.0 °C		5080 - 5080 psi
@Temperature 194 - 194 °F		Average value: 35.0 MPa Grade Count:1
Flexural Modulus 0.255 - 36.2 GPa37.0 - 5250 ksiAverage value: 6.39 GPa Grade Count:290
 0.700 - 15.1685 GPa
@Temperature 60.0 - 120 °C		102 - 2200.03 ksi
@Temperature 140 - 248 °F		Average value: 3.70 GPa Grade Count:4
Compressive Yield Strength 30.3 - 110 MPa4400 - 16000 psiAverage value: 57.0 MPa Grade Count:3
Poissons Ratio 0.3500.350Average value: 0.350 Grade Count:3
Shear Strength 50.0 - 76.5 MPa7250 - 11100 psiAverage value: 61.7 MPa Grade Count:5
Izod Impact, Notched 0.300 - 10.1 J/cm0.562 - 19.0 ft-lb/inAverage value: 1.55 J/cm Grade Count:266
 0.200 - 0.280 J/cm
@Temperature -40.0 - -20.0 °C		0.375 - 0.525 ft-lb/in
@Temperature -40.0 - -4.00 °F		Average value: 1.20 J/cm Grade Count:2
 0.5339 - 2.6695 J/cm
@Temperature -40.0 - -40.0 °C		1.000 - 5.0011 ft-lb/in
@Temperature -40.0 - -40.0 °F		Average value: 1.20 J/cm Grade Count:16
 0.5339 - 2.6695 J/cm
@Thickness 3.17 - 3.17 mm		1.000 - 5.0011 ft-lb/in
@Thickness 0.125 - 0.125 in		Average value: 1.20 J/cm Grade Count:16
Izod Impact, Unnotched 3.20 - 5340 J/cm6.00 - 10000 ft-lb/inAverage value: 9.28 J/cm Grade Count:76
Izod Impact, Notched (ISO) 3.50 - 861 kJ/m²1.67 - 410 ft-lb/in²Average value: 40.2 kJ/m² Grade Count:29
 3.50 - 17.0 kJ/m²
@Temperature -40.0 - -30.0 °C		1.67 - 8.09 ft-lb/in²
@Temperature -40.0 - -22.0 °F		Average value: 9.13 kJ/m² Grade Count:22
Izod Impact, Unnotched (ISO) 30.0 - 100 kJ/m²14.3 - 47.6 ft-lb/in²Average value: 68.2 kJ/m² Grade Count:13
 25.0 - 90.0 kJ/m²
@Temperature -30.0 - -30.0 °C		11.9 - 42.8 ft-lb/in²
@Temperature -22.0 - -22.0 °F		Average value: 62.5 kJ/m² Grade Count:12
Charpy Impact Unnotched 1.30 J/cm² - NB6.19 ft-lb/in² - NBAverage value: 8.00 J/cm² Grade Count:25
 0.800 J/cm² - NB
@Temperature -40.0 - -20.0 °C		3.81 ft-lb/in² - NB
@Temperature -40.0 - -4.00 °F		Average value: 5.82 J/cm² Grade Count:20
Charpy Impact, Notched 0.350 - 2.00 J/cm²1.67 - 9.52 ft-lb/in²Average value: 1.04 J/cm² Grade Count:19
 0.200 - 1.40 J/cm²
@Temperature -40.0 - -20.0 °C		0.952 - 6.66 ft-lb/in²
@Temperature -40.0 - -4.00 °F		Average value: 0.889 J/cm² Grade Count:18
Puncture Energy 2.00 - 2.00 J
@Temperature -30.0 - -30.0 °C		1.48 - 1.48 ft-lb
@Temperature -22.0 - -22.0 °F		Average value: 2.00 J Grade Count:1
Coefficient of Friction 0.100 - 0.2800.100 - 0.280Average value: 0.225 Grade Count:11
Coefficient of Friction, Static 0.0900 - 0.2200.0900 - 0.220Average value: 0.170 Grade Count:11
K (wear) Factor 16.1 - 38.3 x 10-8 mm³/N-M8.00 - 19.0 x 10-10 in³-min/ft-lb-hrAverage value: 31.3 x 10-8 mm³/N-M Grade Count:11
Limiting Pressure Velocity 0.596 - 1.54 MPa-m/sec17000 - 44000 psi-ft/minAverage value: 0.690 MPa-m/sec Grade Count:8
Taber Abrasion, mg/1000 Cycles 5.00 - 7.005.00 - 7.00Average value: 6.00 Grade Count:4
 
Electrical PropertiesMetricEnglishComments
Electrical Resistivity 1.00 - 1.00e+17 ohm-cm1.00 - 1.00e+17 ohm-cmAverage value: 2.87e+15 ohm-cm Grade Count:220
Surface Resistance 1.00 - 1.00e+16 ohm1.00 - 1.00e+16 ohmAverage value: 3.04e+14 ohm Grade Count:90
Dielectric Constant 3.20 - 13.03.20 - 13.0Average value: 4.42 Grade Count:22
Dielectric Strength 15.7 - 120 kV/mm400 - 3050 kV/inAverage value: 23.5 kV/mm Grade Count:194
Dissipation Factor 0.0100 - 0.3200.0100 - 0.320Average value: 0.0686 Grade Count:5
Arc Resistance 95.0 - 185 sec95.0 - 185 secAverage value: 127 sec Grade Count:6
Comparative Tracking Index 225 - 600 V225 - 600 VAverage value: 445 V Grade Count:41
 
Thermal PropertiesMetricEnglishComments
CTE, linear 7.20 - 146 µm/m-°C4.00 - 81.0 µin/in-°FAverage value: 46.2 µm/m-°C Grade Count:196
Specific Heat Capacity 1.67 J/g-°C0.399 BTU/lb-°FAverage value: 1.67 J/g-°C Grade Count:4
Thermal Conductivity 0.200 - 0.260 W/m-K1.39 - 1.80 BTU-in/hr-ft²-°FAverage value: 0.224 W/m-K Grade Count:8
Melting Point 232 - 263 °C450 - 505 °FAverage value: 259 °C Grade Count:86
Maximum Service Temperature, Air 80.0 - 210 °C176 - 410 °FAverage value: 146 °C Grade Count:7
Deflection Temperature at 0.46 MPa (66 psi) 100 - 263 °C212 - 505 °FAverage value: 241 °C Grade Count:206
Deflection Temperature at 1.8 MPa (264 psi) 57.2 - 260 °C135 - 500 °FAverage value: 190 °C Grade Count:290
Vicat Softening Point 150 - 255 °C302 - 491 °FAverage value: 243 °C Grade Count:40
Flammability, UL94 HB - 5VBHB - 5VBGrade Count:177
Flammability Test 1.001.00Average value: 1.00 Grade Count:4
Oxygen Index 26.0 - 31.0 %26.0 - 31.0 %Average value: 28.3 % Grade Count:7
Glow Wire Test 650 - 960 °C1200 - 1760 °FAverage value: 839 °C Grade Count:29
Shrinkage  0.200 - 0.400 %
@Temperature 120 - 120 °C		0.200 - 0.400 %
@Temperature 248 - 248 °F		Average value: 0.300 % Grade Count:1
 0.200 - 0.400 %
@Time 14400 - 14400 sec		0.200 - 0.400 %
@Time 4.00 - 4.00 hour		Average value: 0.300 % Grade Count:1
 
Processing PropertiesMetricEnglishComments
Processing Temperature 260 - 300 °C500 - 572 °FAverage value: 283 °C Grade Count:27
Feed Temperature 60.0 - 270 °C140 - 518 °FAverage value: 86.3 °C Grade Count:24
Nozzle Temperature 250 - 295 °C482 - 563 °FAverage value: 276 °C Grade Count:7
Melt Temperature 238 - 320 °C460 - 608 °FAverage value: 281 °C Grade Count:77
Mold Temperature 26.7 - 110 °C80.0 - 230 °FAverage value: 80.6 °C Grade Count:103
Drying Temperature 71.1 - 107 °C160 - 225 °FAverage value: 79.1 °C Grade Count:84
Dry Time 2.00 - 6.00 hour2.00 - 6.00 hourAverage value: 3.25 hour Grade Count:71
 2.00 - 6.00 hour
@Temperature 79.4 - 80.0 °C		2.00 - 6.00 hour
@Temperature 175 - 176 °F		Average value: 3.06 hour Grade Count:16
Moisture Content 0.0300 - 2.20 %0.0300 - 2.20 %Average value: 0.210 % Grade Count:70
Injection Pressure 4.96 - 138 MPa720 - 20000 psiAverage value: 42.2 MPa Grade Count:39
Hold Pressure 50.0 - 100 MPa7250 - 14500 psiAverage value: 75.0 MPa Grade Count:21
Back Pressure 0.000 - 1.72 MPa0.000 - 250 psiAverage value: 0.534 MPa Grade Count:50
Shot Size 30.0 - 80.0 %30.0 - 80.0 %Average value: 55.0 % Grade Count:17
Screw Speed 20.0 - 140 rpm20.0 - 140 rpmAverage value: 72.0 rpm Grade Count:48

转载请注明: 转自中国塑胶原料之家 http://www.su-jiao.com/wuxingbiao/

本文链接: http://www.su-jiao.com/yuanliaoku/show-44771.html

免责声明: 本文 Overview of materials for Nylon 66, Heat Stabilized 仅代表作者个人观点，中国塑胶原料之家无关。中国塑胶原料之家网所转载的内容，其版权均由原作者和资料提供方所拥有！如因作品版权问题需要处理，请与我们联络

该类别其他物性信息

塑胶原料之家，专业塑料网站、原料报价网站，免费发布塑胶供求信息。塑胶原料之家为您提供塑料供应、塑料求购、塑料行情、塑料展会、塑料原料资讯服务。

2008-2015 塑料|塑胶原料|物性表大全|UL黄卡|SGS报告查询|最新价格--塑胶原料之家

沪ICP备15027283号-4